Juniper QFX5120 Series Скачать руководство пользователя

Страница: 117 / 207

Maintaining the QFX5120 Cooling System

IN THIS SECTION

Removing a Fan Module from a QFX5120 Switch | 121

Installing a Fan Module in a QFX5120 Switch | 122

Removing a Fan Module from a QFX5120 Switch

The fan module in QFX5120 switches is a hot-removable and hot-insertable field-replaceable unit (FRU)

installed in the rear panel of the switch: You can remove and replace it without powering off the switch

or disrupting switch functions.

Ensure that you have the following parts and tools available:

•

Phillips (+) screwdriver, number 2

•

An antistatic bag or an antistatic mat

•

A replacement fan module

NOTE:

The fan module slots are at the left side of the rear panel.

Figure 59 on page 122

shows how

to remove a fan module.

1. Place the antistatic bag or the antistatic mat on a flat, stable surface.

2. Loosen the captive screws on the front faceplate of the fan module by using your fingers. If you are

unable to loosen the captive screws by using your fingers, use the screwdriver.

WARNING:

To prevent injury, do not touch the fan with your hands or any tools as

you slide the fan module out of the chassis—the fan might still be running.

3. Grasp the handle on the fan module and pull it firmly to slide the fan module out of the chassis.

4. Place the fan module in the antistatic bag or on the antistatic mat placed on a flat, stable surface.

121

Содержание QFX5120 Series
















































































































































































































Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды

Juniper QFX5120 Series, Руководство по оборудованию

Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды