Juniper QFX5120 Series Скачать руководство пользователя

Страница: 118 / 207

5. Install the replacement fan.

6. Tighten the captive screws on the faceplate of the fan module by using your fingers. If you are unable

to tighten the captive screws by using your fingers, use the screwdriver.

Figure 59: Removing a Fan Module from a QFX5120 Switch

g022522

NOTE:

Both the fan modules must be installed and operational for optimal functioning of the

switch.

Installing a Fan Module in a QFX5120 Switch

QFX5120-48Y comes with 4+1 redundant fans and QFX5120-32C comes with 5+1 redundant fans. Each

fan module is a hot-removable and hot-insertable field-replaceable unit (FRU) installed in the rear panel

of the switch. You can remove and replace it without powering off the switch or disrupting switch functions.

CAUTION:

Do not mix:

•

Fan modules with different airflow labels (AIR IN (AFI) and AIR OUT (AFO)) in the same

chassis.

•

Power supplies with different airflow labels (AIR IN (AFI) and AIR OUT (AFO)) in the

same chassis.

•

Power supplies and fan modules with different airflow labels (AIR IN (AFI) and AIR

OUT (AFO)) in the same chassis.

•

AC and DC power supplies in the same chassis.

122

Содержание QFX5120 Series
















































































































































































































Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды

Juniper QFX5120 Series, Руководство по оборудованию

Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды