manualshive.com logo in svg

Juniper MX2010, Руководство по оборудованию

Juniper MX2010 - мощный маршрутизатор для крупных сетей. Желающие могут бесплатно скачать его аппаратное руководство с {веб-сайта}. Этот manual поможет вам узнать о всех возможностях и функциях устройства для оптимальной работы с сетями любого масштаба.

Поделиться
Скачать
background image

MX2000 Switch Fabric Board (SFB) Overview

Switch Fabric Boards (SFBs) are the data plane for the subsystems in the MX router chassis. SFBs create

a highly scalable and resilient “all-active” centralized switch fabric that delivers up to 2 Tbps of full-duplex

switching capacity to each MPC slot in an MX2000 router.

There are three models of MX SFBs:

•

MX2000-SFB-S Description

•

MX2000-SFB2-S Enhanced Switch Fabric Board Description

•

MX2000-SFB3 Switch Fabric Board Description

The SFB and SFB2 switch control board models are the same except that the SFB model has three XF

fabric chips per card whereas the SFB2 model has two PF fabric chips per card.

RELATED DOCUMENTATION

MX2000 Switch Fabric Board LED

MX2000 Switch Fabric Board LED

One bicolor LED on the Switch Fabric Board (SFB) indicates the status of the SFB. The LED, labeled

OK/FAIL, is located directly on the SFB.

Table 23 on page 66

describes the functions of the SFB LED.

Table 23: Switch Fabric Board LED

Description

State

Color

Label

SFB is online.

Slow blinking when being

initialized.

Fast blinking when SFB is being

identified by software.

NOTE:

This is used to guide

the operator to correct any

action needed on the SFB.

Green

OK/FAIL

SFB has failed.

On steadily

Red

SFB is offline.

Off

–

66

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX2010

Makita RF1101 Parts Breakdown preview
RF1101
Бренд: Makita Страницы: 2
G-Technology G-DRIVE ev ATC Product Manual preview
G-DRIVE ev ATC
Бренд: G-Technology Страницы: 35
Lanner NCA-1526 User Manual preview
NCA-1526
Бренд: Lanner Страницы: 78
Juniper ACX2000 Hardware Manual preview
ACX2000
Бренд: Juniper Страницы: 190
AMX NXA-ENET8POE Installation Manual preview
NXA-ENET8POE
Бренд: AMX Страницы: 2
VoiceLine InnoMedia MTA 3328-2R Getting Started Manual preview
InnoMedia MTA 3328-2R
Бренд: VoiceLine Страницы: 18
AOpen ISDN SOHO Router User Manual preview
ISDN SOHO Router
Бренд: AOpen Страницы: 89
OST RuggedNet 10G/Si User Manual preview
RuggedNet 10G/Si
Бренд: OST Страницы: 8
Axtrinet APG200 User Manual preview
APG200
Бренд: Axtrinet Страницы: 49
Jatontec JT4500H Quick User Manual preview
JT4500H
Бренд: Jatontec Страницы: 13
D-Link DSL-125 Quick Installation Manual preview
DSL-125
Бренд: D-Link Страницы: 12
Quamtum HotSpot HS2 User Manual preview
HotSpot HS2
Бренд: Quamtum Страницы: 42
IC Realtime Elite Series Quick Start Manual preview
Elite Series
Бренд: IC Realtime Страницы: 8
D-Link DES-1016D - Switch Quick Installation Manual preview
DES-1016D - Switch
Бренд: D-Link Страницы: 32
D-Link Amplifi DIR-657 Technical Specifications preview
Amplifi DIR-657
Бренд: D-Link Страницы: 3
D-Link DES-1005P Manual preview
DES-1005P
Бренд: D-Link Страницы: 16
D-Link DES-1005F Quick Installation Manual preview
DES-1005F
Бренд: D-Link Страницы: 35
D-Link DES-1004 User Manual preview
DES-1004
Бренд: D-Link Страницы: 46

Бренды по названию

Популярные бренды

Загрузить еще бренды