manualshive.com logo in svg

Juniper MX2010, Руководство по оборудованию

Juniper MX2010 - мощный маршрутизатор для крупных сетей. Желающие могут бесплатно скачать его аппаратное руководство с {веб-сайта}. Этот manual поможет вам узнать о всех возможностях и функциях устройства для оптимальной работы с сетями любого масштаба.

Поделиться
Скачать
background image

13. Carefully move the AC power cable out of the way.

14. Disconnect the AC power cord from the AC PDM.

SEE ALSO

Installing an MX2010 Three-Phase Wye AC Power Cord | 586

Preventing Electrostatic Discharge Damage to an MX Series Router

MX2000 Three-Phase Wye AC Power Distribution Module Description | 102

Installing an MX2010 Three-Phase Wye AC Power Cord

To install a three-phase wye AC power cord:

1. Switch off the customer-site circuit breakers to the PDM being removed. Make sure that the voltage

across the AC power source cord is 0 V and that there is no chance that the cord might become active
during the installation process.

2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to

one of the ESD points on the chassis.

3. Switch all the power switches on the PSM faceplates to the off (O) position.

NOTE:

After powering off a PSM, wait at least 60 seconds before turning it back on.

4. Using a number 2 Phillips (+) screwdriver, loosen the four screws on the cover of the metal wiring

compartment that protects the AC terminal block.

5. Remove the cover of the metal AC wiring compartment.

6. Unscrew the retaining nut from the AC power cord.

7. Place the retaining nut inside the metal wiring compartment.

8. Insert the wires of the AC power cord through the hole of the metal wiring compartment.

9. Screw the retaining nut onto the AC power cord to secure it to the metal wiring compartment.

586

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX2010

D-Link PowerLine DHP-W611AV User Manual preview
PowerLine DHP-W611AV
Бренд: D-Link Страницы: 78
D-Link DIR-862L Manual preview
DIR-862L
Бренд: D-Link Страницы: 4
D-Link DIR-860L Quick Install Manual preview
DIR-860L
Бренд: D-Link Страницы: 2
D-Link DIR-850L Resetting Manual preview
DIR-850L
Бренд: D-Link Страницы: 9
D-Link DIR-850L Setup And Installation Manual preview
DIR-850L
Бренд: D-Link Страницы: 8
D-Link DIR-865L Specifications preview
DIR-865L
Бренд: D-Link Страницы: 3
D-Link DIR-867 Quick Install Manual preview
DIR-867
Бренд: D-Link Страницы: 28
D-Link DIR-X1530 Quick Start Manual preview
DIR-X1530
Бренд: D-Link Страницы: 2
D-Link DSL-2540B - ADSL2/2+ Modem With EN Router Quick Install Manual preview
DSL-2540B - ADSL2/2+ Modem With EN Router
Бренд: D-Link Страницы: 12
D-Link DIR-882 Quick Installation Manual preview
DIR-882
Бренд: D-Link Страницы: 62
Lantronix Device Server UDS 10 Hardware Manual preview
Device Server UDS 10
Бренд: Lantronix Страницы: 8
National Instruments NI 9265 Operating Instructions Manual preview
NI 9265
Бренд: National Instruments Страницы: 26
National Instruments NI 9203 User Manual And Specifications preview
NI 9203
Бренд: National Instruments Страницы: 85
National Instruments Module SCXI-1503 User Manual preview
Module SCXI-1503
Бренд: National Instruments Страницы: 79
Oracle Talari E1000 Installation Manual preview
Talari E1000
Бренд: Oracle Страницы: 24
Lancom GS-2310P Instruction Manual preview
GS-2310P
Бренд: Lancom Страницы: 25
ADTRAN NetVanta 6355 PoE Installation Manual preview
NetVanta 6355 PoE
Бренд: ADTRAN Страницы: 46
I-O Wireless WBC11 User Manual preview
WBC11
Бренд: I-O Wireless Страницы: 55

Бренды по названию

Популярные бренды

Загрузить еще бренды