Juniper MX2010 Скачать руководство пользователя страница 529

Страница: 529 / 825

Replacing the MX2010 Air Baffle

Removing the MX2010 Air Baffle | 513

Installing the MX2010 Air Baffle | 514

Removing the MX2010 Air Baffle

To remove the upper air baffle—MX2000-UPR-BAFFLE-A:

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to

one of the ESD points on the chassis.

2. Loosen the four captive screws located on either side of the air baffle that is attached to the upper fan

tray access door.

3. Grasp the air baffle, and pull straight out from the upper fan tray access door as shown in

Figure 270 on page 513

Figure 270: Removing the Air Baffle

g007465

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды

Juniper MX2010, Руководство по оборудованию

Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды