Juniper MX2010 Скачать руководство пользователя страница 403

Страница: 403 / 825

Installing the MX2010 Air Baffle

To install the upper air baffle—MX2000-UPR-BAFFLE-A:

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to

one of the ESD points on the chassis.

2. Ensure that the air baffle louvers are closed.

3. Close the upper fan tray access door.

4. Align the holes on the air baffle with the holes located on either side of the upper fan tray access door,

(see

Figure 178 on page 387

5. Tighten the four captive screws to secure the air baffle to the upper fan tray access door.

6. Open the air baffle louvers to direct the exhaust air away from the router. To direct exhaust air away

from the router, the louvers on the air baffle must be set to a 10-degree fixed upward tilt with respect

to the horizontal.

Figure 178: Installing the Air Baffle

g007466

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды

Juniper MX2010, Руководство по оборудованию

Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды