Juniper MX2010 Скачать руководство пользователя страница 459

Страница: 459 / 825

•

If the OK/FAIL LED is yellow, remove and install the CB-RE again. If the OK/FAIL LED still lights

steadily, the CB-RE is not functioning properly. Contact your customer support representative. See

“Contacting Customer Support” on page 731

7. Check the status of the CB-RE by using the show chassis environment cb command.

Figure 211: Installing a CB-RE

g007420

OK/FAIL

The CB-RE might require several minutes to boot. After the CB-RE boots, verify that it is installed correctly

by checking the FAIL, RE0, and RE1 LEDs on the craft interface. If the router is operational and the CB-RE

is functioning properly, the green ONLINE LED on the CB-RE lights steadily. If the red FAIL LED lights

steadily instead, remove the CB-RE and reinstall it. If the red FAIL LED on the CB-RE still lights steadily,

the CB-RE is not functioning properly. Contact your customer support representative.

Verifying and Configuring the Upgraded CB-RE

After replacing the CB-RE with the REMX2K-X8-64G CB-RE, perform the following steps:

1. Verify that the REMX2K-X8-64G CB-RE is online by issuing the show chassis hardware and show

chassis routing-engine |no-more commands.

Verify the software by using the show vmhost status and show vmhost version commands.

2. After you install the REMX2K-X8-64G CB-RE, the CB-RE gets automatically powered on and comes

up in amnesiac mode as it is loaded with factory defaults. After the CB-RE comes up in amnesiac mode,
load the base configuration and commit.

443

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды

Juniper MX2010, Руководство по оборудованию

Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды