Juniper JUNOS Скачать руководство пользователя | Manualshive

Страница: 105 / 722

background image

Using the Basic Monitoring Method

!

69

Chapter 11: Understanding the Method and Tools for Monitoring Router Components

Power supplies

A power supply was removed
from the chassis.

Insert a power supply into
an empty slot.

Yellow

A power supply temperature
sensor failed.

Replace the failed power
supply or power entry
module.

Yellow

A power supply fan failed.

Replace the failed power
supply fan.

Yellow

A power supply has high
temperature.

Replace the failed power
supply or power entry
module.

Red

A 5V power supply has failed. Replace the failed power

supply or power entry
module.

Red

A 3.3V power supply failed.

Replace the failed power
supply or power entry
module.

Red

A 2.5V power supply failed.

Replace the failed power
supply or power entry
module.

Red

A power supply input failed.

Check the power supply
input connection.

Red

A power supply has failed.

Replace the failed power
supply or power entry
module.

Red

Routing Engine

Error in reading or writing
hard disk.

Reformat the hard disk and
install a bootable image. If
this fails, replace the failed
Routing Engine.

Yellow

Error in reading or writing
compact flash.

Reformat the compact flash
and install a bootable
image. If this fails, replace
the failed Routing Engine.

Yellow

System booted from default
backup Routing Engine. If
you manually switched
mastership, ignore this alarm
condition.

Install a bootable image on
the default master Routing
Engine. If this fails, replace
the failed Routing Engine.

Yellow

System booted from hard
disk.

Install a bootable image on
the compact flash. If this
fails, replace the failed
Routing Engine.

Yellow

Compact flash missing in
boot list.

Replace the failed Routing
Engine.

Red

Hard disk missing in boot
list.

Replace the failed Routing
Engine.

Red

Routing Engine failed to
boot.

Replace the failed Routing
Engine.

Red

SCB

The SCB failed. If this occurs,
the board attempts to reboot.

Replace the failed SCB.

Red

Chassis
Component

Alarm Condition

Remedy

Alarm
Severity

«
...
103
104
105
106
107
...
»

Содержание JUNOS



















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOS

C8 - DocuPrint Color Inkjet Printer

Бренд: Xerox Страницы: 458

Бренд: Xerox Страницы: 2

C8 - DocuPrint Color Inkjet Printer

Бренд: Xerox Страницы: 51

Бренд: PS Audio Страницы: 6

MOBILE SECURITY FOR WINDOWS MOBILE -

Бренд: F-SECURE Страницы: 35

GZ-MG77 - Camcorder - 2.2 MP

Бренд: JVC Страницы: 72

Бренд: Ulead Страницы: 168

Cycos ERGO mrs 5.0

Бренд: Cycos Страницы: 46

PC ANYWHERE SOLUTION V 12.5

Бренд: Symantec Страницы: 63

Бренд: 3Com Страницы: 44

MOBILE SECURITY 6 FOR ANDROID

Бренд: F-SECURE Страницы: 22

DREAMWEAVER 8-GETTING STARTED WITH...

Бренд: MACROMEDIA Страницы: 326

Бренд: KAPERSKY Страницы: 298

Бренд: IVT Страницы: 49

Loran TD Position

Бренд: Garmin Страницы: 11

GZ-MG505US - Camcorder - 1.33 MP

Бренд: JVC Страницы: 72

Бренд: Kenwood Страницы: 44

ThinkCentre Edge 91

Бренд: Lenovo Страницы: 262

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды