Jungheinrich ESD 220 Скачать руководство пользователя | Manualshive

Страница: 127 / 186

background image

3.4

Hydraulic system

WARNING!

Leaky hydraulic systems can result in accidents

Hydraulic oil can escape from leaky and faulty hydraulic systems.

u

Report any defects immediately to your supervisor.

u

Mark defective truck and take out of service.

u

Do not return the industrial truck to service until you have identified and rectified
the fault.

u

Remove any spilled hydraulic immediately with an appropriate bonding agent.

u

The bonding agent / consumable mixture must be disposed of in accordance with
regulations.

WARNING!

Faulty hydraulic hoses can result in injury and infection

Pressurised hydraulic oil can escape from fine holes or hairline cracks in the
hydraulic hoses. Brittle hydraulic hoses can burst during operation. People standing
near the truck can be injured by the hydraulic oil.

u

Call for a doctor immediately in the event of an injury.

u

Do not touch pressurised hydraulic hoses.

u

Report any defects immediately to your supervisor.

u

Mark defective truck and take it out of service.

u

Do not return the industrial truck to service until you have identified and rectified
the fault.

NOTICE

Testing and replacing hydraulic hoses

Hydraulic hoses can become brittle through age and must be checked at regular
intervals. The application conditions of the industrial truck have a considerable
impact on the ageing of the hydraulic hoses.

u

Check the hydraulic hoses at least annually and replace if necessary.

u

If the operating conditions become more arduous the inspection intervals must be
reduced accordingly.

u

In normal operating conditions a precautionary replacement of the hydraulic hoses
is recommended after 6 years. The owner must carry out a risk assessment to
ensure safe, prolonged use. The resulting protection measures must be observed
and the inspection interval reduced accordingly.

125

10.19 en-GB

«
...
125
126
127
128
129
...
»

Содержание ESD 220



























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ESD 220

TRX500FA Fourtrax Foreman Rubicon

Бренд: Honda Страницы: 242

Бренд: Tao Motor Страницы: 80

Centennial A-130-12R

Бренд: Etnyre Страницы: 20

Бренд: Leggero Страницы: 98

Minor VM Hydrostatic

Бренд: Scarab Страницы: 32

Бренд: KTM Страницы: 211

2008 450 XC ATV

Бренд: KTM Страницы: 223

OFF ROAD AMBUSH iS

Бренд: Bad Boy Страницы: 156

Бренд: Parklands Страницы: 66

1966 Snow Cruiser C-1560

Бренд: OMC Страницы: 20

Бренд: Kellfri Страницы: 12

Бренд: American Sportworks Страницы: 13

Бренд: Yamaha Страницы: 148

Бренд: Yamaha Страницы: 184

2009 LT-A750XK9

Бренд: Suzuki Страницы: 711

Бренд: Panther Страницы: 10

AUTOMIZER HELPING-HAND

Бренд: Labrie Страницы: 118

Бренд: Yamaha Страницы: 1664

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды