background image

Switch actuator / blinds actuator

Operating an output in manual mode

Activate short-term or permanent manual operation.

Press button 

ǃ

 (1) repeatedly until LED A1... (4) of the desired output or output pair

flashes.

Press button 

DŽ

 (9) or 

Dž

 (10).

Short: Switch on/off, drive stop
Long: Move blind/shutter upwards/downwards
LED 

DŽ

 (3) ON: Relay output closed

LED 

Dž

 (6) OFF: Relay output opened

Short-term manual operation: After running through all of the outputs the device exits
manual mode after another brief press.

Switching off all outputs / Stopping all hangings

The device is in continuous manual mode.

Press the ALL OFF button (7).
Switching outputs: All outputs switch off (NO operating mode: relay output opened/NC op-
erating mode: relay output closed).

Venetian blind outputs: All blinds/shutters stop.

Disabling outputs

The device is in continuous manual mode. The bus control can be disabled (ETS parameter).

Press button 

ǃ

 (6) repeatedly until LED A1... (4) of the desired output or output pair

flashes.

Press the/ 

DŽ

 (9) and / 

Dž

 (10) buttons simultaneously for approx. 5 s.

Selected output is disabled.

The status LED A1... (4) of the selected output or output pair flashes quickly.

A disabled output can be operated in manual mode.

Re-enabling outputs

The device is in continuous manual mode. One or more outputs were disabled in manual mode.

Press button 

ǃ

 (6) repeatedly until the output to be unlocked or the output pair is selec-

ted.

Press the/ 

DŽ

 (9) and / 

Dž

 (10) buttons simultaneously for approx. 5 s.

Disabling is deactivated.

The LED A1... (4) of the selected output or output pair flashes slowly.

5

Information for electrically skilled persons

 DANGER!

Mortal danger of electric shock.

Disconnect the device. Cover up live parts.

5.1 Fitting and electrical connection

Fitting the device

In secure operation (preconditions):

Secure commissioning is activated in the ETS.

Device certificate entered/scanned or added to the ETS project. A high resolution camera
should be used to scan the QR code.

5 / 9

82402603

15.05.2020

J0082402603

Содержание 230061SR










Отзывы: