Jula Meec tools 001-115, Руководство по эксплуатации, Страница: 62 / 68

EN
62
Other
Border wire signal S1 is selected.
Border wire signal S2 is selected.
STOP has been pressed. The robotic lawn mower has
stopped.
PIN code
The first time you start the robotic lawn mower it is locked with a PIN code
set at the factory.
1. Press the lock symbol to show the screen image to enter the PIN
code. The factory set PIN code is 0000.
2. Press the 0 button 4 times to enter the PIN code and unlock the
robotic lawn mower.
3. A black dot is shown on the display instead of the entered digit, to
show which position in the PIN code should be entered.
4. The normal control panel is shown on the touch screen after the entry.
FIG. 23
5. To change the PIN code, see the section Changing the PIN code .
Settings
Date and time
1. Press Set to the left of the touch screen and then . The digits for
the date and time flash.
2. Set the correct date with the buttons and .
3. When the correct digits are shown, press Set and set the next digit.
FIG. 24
4. If no settings are made within 15 seconds the touch screen shows the
normal control panel again. The setting can be closed by pressing
anywhere on the touch screen.
NOTE:
The date and time must be set for the robotic lawn mower to work
properly.
Setting the mowing schedule (weekday and time)
1. Press the required weekday (Mon to Sun) on the touch screen. The
selected weekday is shown with a frame on the display. A weekday is
shown with a frame on the display to indicate that the robotic lawn
mower is programmed to mow on this day.
2. Press the required time interval (09:00–11:00, 11:00–14:00, 14:00–
19:00, 19:00–09:00) on the touch screen. A selected time interval is
shown with a frame on the display to indicate that the robotic lawn
mower is programmed to mow during this time interval.
FIG. 25
3. From the factory the robotic lawn mower is programmed to mow 24
hours per day every day of the week. We recommend the user sets
the weekdays and times according to what is needed.
NOTE:
The times are not fully optional. It is only possible to choose between
the 4 preset time intervals.
The table shows how many mowing hours per day the different settings give.
FIG. 26
Mowing area Recommended mowing time/day
300 m² 2 h
600 m² 5 h
800 m² 8 h
Setting the border wire signal
• The robotic lawn mower has two border wire signals, signal 1 and
signal 2. If the same type of robotic lawn mower is used in adjacent
gardens we strongly recommend that they are set to different signals
to avoid interference.
• When the border wire is connected to the charging station check
which signal (S1 or S2) the charging station issues. Press the SIGNAL
button to select S1 or S2.
FIG. 27
• Press S1 or S2 on the touch screen to set the same signal on the
charging station.
FIG. 28
Mowing
• Press Start and close the panel. The robotic lawn mower starts
mowing.
• The blade symbol starts rotating.
• The residual battery charge is monitored and shown during the
mowing.
Shows that the battery is fully charged.
Shows that the battery has a 75% charge.
Shows that the battery has a 50% charge.
Shows that the battery has a 30% charge. At this level
the robotic lawn mower goes to the charging station
to be charged.
Shows that the battery is discharged.
Shows that the robotic lawn mower is searching for
the charging station.
Stops rotating to show that the robotic lawn mower is
not mowing on the way to the station.
Mowing height
NOTE:
Always switch off the robotic lawn mower before adjusting the mowing
height.
• The robotic lawn mower has 5 mowing height settings from 20 to 60 mm.