JUKI MF-7500 Series Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 31

background image

– 14 –

– 14 –

‒ 14 ‒

Decrease the presser foot pressure as low as possible to
such an extent that stitches are stabilized.
To adjust the pressure, loosen lock nut

❷

of presser

spring regulator

❶

and turn presser spring regulator

❶

.

After the adjustment, tighten lock nut

❷

.

Turning it clockwise to increase the pressure.
Turning it counterclockwise to decrease the pressure.

6. Adjusting the presser foot pressure

7. Adjusting the thread tension

Adjust the thread tension with the following thread tension
nuts.

❶

Needle thread tension nut

❷

Top covering thread tension nut

❸

Looper thread tension nut

Turn clockwise to increase the thread tension.
Turn counterclockwise to decrease the thread tension.

B

=

Decrease

A

=

Increase

❶

❷

❶

❷

❸

A

B

«
...
14
15
16
17
18
...
»

Содержание MF-7500 Series
































Отзывы:

Нет отзывов

Похожие инструкции для MF-7500 Series

Бренд: Janome Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Happy Страницы: 9

Бренд: Janome Страницы: 2

Бренд: Janome Страницы: 75

Бренд: Janome Страницы: 40

Бренд: Janome Страницы: 45

Бренд: Janome Страницы: 51

Бренд: Janome Страницы: 2

MEMORY CRAFT 9700

Бренд: Janome Страницы: 110

Memory Craft 3000

Бренд: Janome Страницы: 42

Memory Craft 10001

Бренд: Janome Страницы: 181

Бренд: Janome Страницы: 41

Бренд: Janome Страницы: 32

Бренд: Tornado Страницы: 11

Memory Craft 6300P

Бренд: Janome Страницы: 69

Бренд: Duerkopp Adler Страницы: 80

Бренд: R.P.S. Corporation Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды