JUKI LZ-2280A Series Скачать руководство пользователя страница 22

Страница: 22 / 28

– 20 –

(1) Position of the feeding wire

Adjust the installing position of the feeding wire

❶

that a distance of 8 to 10 mm is provided between the
guide portion

❷

of the thread guide and the top end

of the wire. Then, tighten the two screws

❸

(2) Adjusting the stroke of the feeding wire

1) Increase the feeding amount of the needle thread

if the needle thread fails to interlace with the
bobbin thread or is likely to slip out of the needle
eyelet at the start of sewing.

2) Loosen two setscrews

❹

. Shift thread draw-out

wire

❶

in the direction of the arrow.

(3) When turning OFF the feeding device

If it is not necessary to operate thread draw-out wire

❶

, turn off draw-out switch

❺

on the rear face of the

sewing machine.

If the feeding amount of the needle thread is

excessive, the thread will be likely to break.

At this time, adjust the longitudinal po-

sition of thread draw-out wire

❶

so that

thread draw-out wire is brought to the ap-

proximate center of thread take-up thread

guide

❷

1) Align the marker dot

❶

engraved on the pulley

cover with the white marker dot

❷

engraved on

the handwheel (the 3rd white marker dot in terms
of the direction of rotation of the sewing machine).

2) Move the rod

❸

in the direction of the arrow, and

adjust the clamping screw

❺

so that an approxi-

mate 2 mm clearance is provided between the
top end of the needle and the wiper

❹

3) For the sewing machine provided with a wiper,

turn off wiper seesaw switch

❻

in the case the

wiper is not necessary to be used.

4-14. Needle thread feeding device

4-15. Position of the wiper

WARNING :

To protect against possible personal injury due to abrupt start of the machine, be sure to start the

following work after turning the power off and ascertaining that the motor is at rest.

WARNING :

To protect against possible personal injury due to abrupt start of the machine, be sure to start the

following work after turning the power off and ascertaining that the motor is at rest.

❶

❷

❹

❸

8 to 10 mm

❶

❷

❺

❸

❹

❺

2 mm

❻

❶

❷

Содержание LZ-2280A Series





























Результаты поиска

Содержание LZ-2280A Series

Отзывы:

Похожие инструкции для LZ-2280A Series

Бренды по названию

Популярные бренды

JUKI LZ-2280A Series, Инструкция по эксплуатации

Результаты поиска

Содержание LZ-2280A Series

Отзывы:

Похожие инструкции для LZ-2280A Series

Бренды по названию

Популярные бренды