JUKI J-350QVP Скачать руководство пользователя страница 24

Страница: 24 / 32

– 23 –

When you press the "start button" on the right handlebar, the

sewing machine will start sewing according to your settings.

When you press the "start button" again, the sewing machine will

stop sewing.

CAUTION

・

Don’t put any heavy objects on the quilting frame and don’t put

a load heavier than normal sewing.

・

Be careful of surrounding people and objects since you move

the machine and sew.

・

If you move the assembled quilting frame, some parts may be

damaged or bent.

When moving the quilting frame, disassemble it, and then reas-

semble it correctly after it has been delivered.

* Use the screwdriver included with the sewing machine to re-

move any hazardous sharp shavings from the disassembled
quilting frame and other components, as there is a risk of injury
from such hazardous sharp points.

The following functions can be assigned to the left button using the
custom switch/pedal switch.

❶

Thread trimmer ........................Thread trimming is carried out

❷

Needle travel up/down ............Needle is moved by a half stitch

(i.e., needle goes up or comes down)

(Initial setting)

❸

One stitch

(without thread trimming)........ One stitch is sewn

❹

One stitch Thread trimmer .....One stitch is sewn. Then, thread

trimming is carried out.

❺

Two stitch Thread trimmer ......Two stitches are sewn. Then,

thread trimming is carried out.

❻

Three stitch Thread trimmer ...Three stitches are sewn. Then,

thread trimming is carried out.

❶

❸

❷

❻

❹

❺

Содержание J-350QVP
































Результаты поиска

Содержание J-350QVP

Отзывы:

Бренды по названию

Популярные бренды

JUKI J-350QVP, Инструкция по эксплуатации

Результаты поиска

Содержание J-350QVP

Отзывы:

Бренды по названию

Популярные бренды