JUKI J-350QVP Скачать руководство пользователя страница 11

Страница: 11 / 32

– 10 –

Panel cord binding procedure

❶

Remove two setscrews from the presser regulator cover.

Remove the presser regulator cover.

❷

Arrange the panel cord as illustrated in the figure. Then, secure

the cable with a cable clip band.

It is necessary to place the panel cord at a position where the cord

does not come in contact with the mechanical parts.

❸

Align the notch in the cover with the panel cord.

❹

Fix the presser regulator cover with the setscrews.

CAUTION

Turn OFF the power switch.

Always must be disconnected plug from socket-outlet.

❺

❶

❷

❸

❹

❻

Installing the eye protection cover

1. Place eye protection cover

❷

and washer

❸

in the written order

on eye protection cover mounting plate

❶

and fix them with set

screw

❹

2. Install eye protection cover mounting plate

❶

on frame

❻

with

two setscrews

❺

DANGER

Be sure to install the eye protection cover since the cover protects

eyes from being injured by a fragment of a broken needle.

CAUTION

Turn OFF the power switch.

Always must be disconnected plug from socket-outlet.

❶

❸

❷

❹

Содержание J-350QVP
































Результаты поиска

Содержание J-350QVP

Отзывы:

Бренды по названию

Популярные бренды

JUKI J-350QVP, Инструкция по эксплуатации

Результаты поиска

Содержание J-350QVP

Отзывы:

Бренды по названию

Популярные бренды