JUKI HZL-30Z Скачать руководство пользователя | Manualshive

Страница: 15 / 20

background image

4-11 Adjusting the bobbin thread tension

Remove the throat plate.

1. Position the bobbin case and the tension gauge as illustrated and adjust the adjusting
screw

(4)

so that the tension is 0.1862±0.0098 [N] (19g±1g) with SHAPPE

#60 thread.

How to adjust

Bobbin case

Bobbin thread should not come
in contact with bobbin case.

Tension gauge

Tension gauge

4-12 Opening amount of the tension disk

Remove the face cover and the front panel.

1. Turn the adjusting screw in the thread
tension disk floating plate and adjust
so that the clearance between tension
disk (A) and tension disk (B) is 1 mm
when the thread tension dial is set to
the maximum and the presser lifting
lever is raised.

How to adjust

Adjusting

screw

Disk A

Disk B

-13-

-13-

-13-

-13-

-13-

(4)

1 mm

Thread tension
disk floating plate

«
...
13
14
15
16
17
...
»

Содержание HZL-30Z





















Отзывы:

Нет отзывов

Похожие инструкции для HZL-30Z

Бренд: Janome Страницы: 68

Бренд: Janome Страницы: 19

Бренд: Fellowes Страницы: 4

Jet Blaster 900

Бренд: PFX Страницы: 9

Бренд: Singer Страницы: 15

Бренд: National Страницы: 27

Easy Step Plus MS 80

Бренд: Impex Страницы: 9

Бренд: Nilfisk-ALTO Страницы: 27

Бренд: Shark Страницы: 41

Бренд: Brother Страницы: 262

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 11

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 56

Бренд: Panasonic Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды