JRC Alphatron Marine AlphaTurn Скачать руководство пользователя

Страница: 5 / 57

Reverse polarity protection

This is a part of the power supply hardware that prevents any damage to the equipment
when the power supply is connected to the wrong polarity.

ROT signal

Rate Of Turn (ROT) signal indicates the course change of a ship in degrees per minute.
This signal can be analog using voltage or current, or can be an NMEA data signal.

Heading/bearing repeaters

Navigation type of instruments displaying the heading/course of a ship.

Baud rate

This is the transmission speed of serial interfaces in characters per second.

Transmitting interval

The frequency at which complete NMEA sentences are being transmitted in number of
times per second.

Factory setting

Instrument setting for backlight color, language, number of connected apparatus, etc. as
configured as a new instrument by the factory.

Flash memory

Non-volatile type of memory. This type of memory retains its contents even when the
instrument is turned off.

Firmware

(Embedded) software inside the processors of the AlphaLine instrument.

Compass safe distance

The minimum distances to equipment that will not cause an unacceptable deviation of
the ship's standard and steering compasses.

Table 1: Definitions

I.2.2 Abbreviations

Abbreviations as used in this manual are explained in Table 2: Abbreviations on page 5.

Ampere

ARD

AlphaLine Repeater Display

CAN

Controller Area Network

Direct Current

Dynamic Position

ECDIS

Electronic Chart Display Information System

GPS

Global Positioning System

I/O

Inputs and Outputs

I.S.

Inter Switch

LED

Light-Emitting Diode

Milliampere

Millimeter

Normally Closed

NMEA

National Marine Electronics Association

Normally Open

Operational Alarm

TAP

Type Approval Program

PCB

Printed Circuit Board

RCU

Remote Control Unit

5 | Preface

Содержание Alphatron Marine AlphaTurn


























































Результаты поиска

Содержание Alphatron Marine AlphaTurn

Отзывы:

Похожие инструкции для Alphatron Marine AlphaTurn

Бренды по названию

Популярные бренды

JRC Alphatron Marine AlphaTurn, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Alphatron Marine AlphaTurn

Отзывы:

Похожие инструкции для Alphatron Marine AlphaTurn

Бренды по названию

Популярные бренды