JRC Alphatron Marine AlphaDynaPos Скачать руководство пользователя | Manualshive

Страница: 37 / 86

background image

37 | Operation

2.3.1.7 Environmental Settings

The Environmental Settings are displayed at the bottom of the MAP screen. See Figure 27: Wind and Current
Compensation on page 37.

Environmental settings include Wind and Current compensation. See Wind Compensation on page 37 for use of wind
and current settings.

Figure 27: Wind and Current Compensation

2.3.1.8 Wind Compensation

The wind compensation force is calculated with parameters setup during commissioning and with actual sensor values.
The parameter describes the vessels' wind area in transversal and longitudinal direction. The formulas to calculate
compensation forces include wind area, wind speed and wind direction. The wind speed is retrieved from wind sensors.
When multiple wind sensors are available, the average of these sensors is used.

Settings for wind compensation are:

•

check box to enable/disable wind compensation. SeeFigure 27: Wind and Current Compensation on page 37.

•

0

∼

100% wind compensation (parameter adjustable) to reduce the compensation thrust.

Use percentage compensation factor of 100% by default and lower it when too much compensation force is used. This
may occur when the vessel is behind an object while the wind sensors are not.

•

When taking station in control Wind Compensation is off by default.

•

Wind Compensation can be switched on by using the check box or button on operator panel.

•

Wind Compensation setting is for all modes.

Note Wind compensation settings remain the same when changing between operator modes. For example
when wind correction is enabled in auto position mode, it remains enabled after changing to joystick manual
mode.

Note The independent joystick system does not synchronize wind settings with the DP system.

2.3.1.9 Current Compensation

Current compensation force is calculated with parameters setup during commissioning and values from position sensor
and actual forces used on the thrusters. The parameters are determined by the part of the vessel that is underneath the
water line and include length, beam and draft. The position sensors give the speed of the vessel.

Information display about current compensation: See Figure 27: Wind and Current Compensation on page 37.

•

Indication of the mode for current compensation:

OFF: The current compensation is off.

ON: The system automatically calculates the values for the current speed and angle from the thruster load and
vessels' speed and wind. These values are most accurate if the vessel is in a steady position. The calculation takes
several minutes to find the optimal value.

•

During Autopilot mode the current compensation is OFF.

•

During Joystick Manual and Joystick Auto mode the current compensation is OFF.

•

During Auto position mode the current compensation is ON.

«
...
35
36
37
38
39
...
»

Содержание Alphatron Marine AlphaDynaPos























































































Отзывы:

Нет отзывов

Похожие инструкции для Alphatron Marine AlphaDynaPos

Бренд: NEC Страницы: 29

Бренд: Patlite Страницы: 28

Web Ankle Brace

Бренд: Darco Страницы: 2

Бренд: Darkly Labs Страницы: 13

Бренд: DARAY Страницы: 24

Body Armor Night Splint

Бренд: Darco Страницы: 2

Бренд: LaboGene Страницы: 59

Бренд: Madrigal Страницы: 5

Бренд: MacDon Страницы: 504

Бренд: ValueStore US Страницы: 2

Contrology Cadillac

Бренд: Balanced Body Страницы: 7

Бренд: MAGSTIM Страницы: 86

Team Agile Color Tune TM16-0

Бренд: GRAU Страницы: 24

Бренд: Hoist Fitness Страницы: 17

Бренд: Peak Pilates Страницы: 4

Бренд: Toro Страницы: 12

ARCHISHAPE 2.0 Linear

Бренд: Osram Страницы: 7

LED Niova 150-F Pro 150W Bi Color

Бренд: Walimex Pro Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды