JRC Alphatron AlphaPilot MFS страница 37 Скачать руководство пользователя | Manualshive

Страница: 37 / 49

background image

37 |

Alarms

, warnings, and cautions

6

Alarms, warnings, and cautions

The AlphaPilot MFS system is comprehensively equipped with alarm mechanisms that continuously
monitor the operational integrity of a wide range of functions from heading input data to steering
gear response.

Alarms, warnings, and cautions are displayed on the AlphaPilot MFS Control Unit. An Alert symbol
will be shown, accompanied with or without an audible signal.

The alert messages listed Appendix A: Alphatron MFS Alerts will be displayed (if appropriate) and will
be accompanied by the appropriate Alert symbol.

Warnings and alarms are accompanied by an audible signal unless the audible alarm has been muted.

The alert messages are also transmitted to BAM (Bridge Alert Management) system if applicable.

Alerts are acknowledged by pressing the Alert indicator or via the BAM system.

NOTE: The Off-heading alert is defined by DNV/GL as a category A alert and therefore it is not
possible to acknowledge this alert remotely from the BAM system.

«
...
35
36
37
38
39
...
»

Содержание Alphatron AlphaPilot MFS


















































Отзывы:

Нет отзывов

Похожие инструкции для Alphatron AlphaPilot MFS

Бренд: Daavlin Страницы: 13

Бренд: Daavlin Страницы: 27

Бренд: ACDC Страницы: 4

Бренд: Parker Страницы: 5

Бренд: Bacharach Страницы: 31

Бренд: Bacharach Страницы: 2

Бренд: Barreto Страницы: 20

Бренд: Barreto Страницы: 18

Бренд: Backyard Discovery Страницы: 41

Бренд: Hammer Страницы: 42

Бренд: U-Line Страницы: 6

Бренд: Kamar Страницы: 2

Бренд: DC Med Страницы: 2

Бренд: RAB Страницы: 7

Airstream PNEG-362 2000 Series

Бренд: GSi Страницы: 18

Бренд: LIGMAN Страницы: 8

Бренд: Tarter Страницы: 18

Бренд: laerdal Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды