JRC Alphatron AlphaPilot MFS Скачать руководство пользователя | Manualshive

Страница: 33 / 49

background image

33 |

Menus

5.1.2

Display cleaning

Figure 7

: Menu item ‘

Display cleaning

’

The purpose of the Clean Mode feature is to clean the surface of the touch screen without
accidentally activating a function. When the Clean mode is started, the touch screen will be
deactivated for 60 seconds. Within this period the instrument will remain functional, but it is not
operable. Except when an indication is activated, then the touch screen will be activated
immediately, and the instrument will be operable again.

To start Clean Mode, perform the following procedure:

1.

Press the

CONFIRM CLEANING THE SCREEN

button to start the Clean Mode.

2.

The AlphaPilot MFS Control Unit starts the countdown sequence. The touch screen is now
deactivated, and the surface can be cleaned. After 60 seconds, or at an active alert, the
instrument will become operable again.

NOTICE

For safety reason, if an alert is active and needs attention of the operator, Clean
Mode can not be started.

«
...
31
32
33
34
35
...
»

Содержание Alphatron AlphaPilot MFS


















































Отзывы:

Нет отзывов

Похожие инструкции для Alphatron AlphaPilot MFS

Бренд: Rabe Страницы: 65

Бренд: Makita Страницы: 8

Бренд: VECTECH Страницы: 5

Бренд: Tascam Страницы: 8

Бренд: B-K lighting Страницы: 5

Бренд: B-K lighting Страницы: 4

Бренд: B-K lighting Страницы: 3

Бренд: made for movement Страницы: 51

Бренд: M-Audio Страницы: 25

Бренд: Maico Страницы: 55

Бренд: Maico Страницы: 38

Бренд: Maico Страницы: 2

Бренд: MAHA Maschinenbau Haldenwang Страницы: 13

Бренд: SandenVendo Страницы: 19

Бренд: SANDIA aerospace Страницы: 10

Бренд: Labnet Страницы: 12

Бренд: Waters Страницы: 4

Бренд: Waterpik Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды