background image

 

 

                     

 

 

Sliding Gate Operator 

User's Manual

 

SL600AC

 

 

 

 
 
 
 
 
 
 

 

 

 

 

 

SL600AC SLIDING GATE OPERATOR 

                                                                                       

1

1. Products introduction 
Please read the instructions carefully before proceeding. 
MCU is supplied to control the gate operator. 
Keypad / single button interface. 
Have Infrared safety sensor interface. 
Soft start and soft stop function and the soft stop width are 
adjustable, and the soft start function can be disabled. 
Working time is adjustable. 
Motor output torque is adjustable. 
Manual key release designed for emergency purposes.

 

 
2. Important safety information 

Carefully read and follow all safety precautions and warning before 

attempting to install and use this automatic gate operator. 

z

  The gate operator should be installed by a qualified technician; 

otherwise, serious personal injury or property damage may 

occur. 

z

  When opening or closing the gate, do not attempt to walk or 

drive through the gate. 

z

  If enable the auto-close function, must use the infrared sensor. 

z

  Children should not be allowed to play near or operate automatic 

gates. 

z

  The automatic gate operator must be grounded.

 

z

  Install the gate operator on the inside of the property; DO NOT 

install it on the outside of the property where the public has 

Содержание SL600AC












Отзывы: