background image

2

 

 

 
SAFETY AND PROPER USAGE

 

To ensure safe and enduring performance of this product, you must comply strictly with the instructions enclosed herein. Non-compliance with instructions or 
improper handling of the product will void your warranty! Usage of this product in conditions not specified in this manual or in contrary to the instructions hereby 
provided is considered IMPROPER. The manufacturer will not be held liable for any damages resulting from improper use of the product.

 

SAFETY & WARNING INSTRUCTIONS

 

- Observe valid and generally accepted safety rules when planning, installing and using this product. 

- Take proper measures to prevent unintentional operation of the product or damage to it. 

- Do not attempt to disassemble this product or lines in the system while they are under pressure. 

- Always depressurise the compressed air system before working on the system. 

It is important that personnel use safe working practices and observe all regulations and legal requirements for safety when  operating this product. When 
handling, operating or carrying out maintenance on this product, personnel must employ safe engineering practices and observe all local health & safety 
requirements & regulations. International users refer to regulations that prevail within the country of installation. Most accidents, which occur during the  
operation and maintenance of machinery, are the result of failure to observe basic safety rules or precautions. An accident can often be avoided by recognising 
a situation that is potentially dangerous. Improper operation or maintenance of this product could be dangerous and result in an accident causing injury or 
death. The manufacturer cannot anticipate every possible circumstance, which may represent a potential hazard. The WARNINGS in this manual cover the most 
common potential hazards and are therefore not all-inclusive. If the user employs an operating procedure, an item of equipment or a method of working which 
is not specifically recommended by the manufacturer he must ensure that the product will not be damaged or made unsafe and that there is no risk to persons 
or property.   
 

GENERAL MAGNET SAFETY

 

The magnets in the operator we use are extremely strong, and must be handled with care to avoid personal injury and damage to the magnets. Fingers and 
other body parts can get severely pinched between two attracting magnets. The strong magnetic fields of the magnets in the operator can also damage 
magnetic media such as floppy disks, credit cards, magnetic I.D. cards, cassette tapes, video tapes or other such devices. They can also damage televisions, VCRs, 
computer monitors and other CRT displays. Never place the operator near electronic appliances. Never allow magnets near a person with a pacemaker or similar 
medical aid. The strong magnetic fields of the magnets in the operator can affect the operation of such devices. The operator will lose its magnetic properties if 
heated above 175 °F (80 °C). 
 

NEVER CHANGE ORIGINAL COMPONENTS WITH ALTERNATIVES

 

Содержание magy












Отзывы: