Jonsered LT2218CMA Скачать руководство пользователя страница 26

Страница: 26 / 32

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right)

when wheels are positioned straight forward, remove steer-

ing wheel and reassemble per instructions in the Assembly

section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on

your tractor. If damage has occurred to affect the front

wheel toe-in or camber, contact your nearest authorized

service center/department.

SERVICE AND ADJUSTMENTS

02239

ADJUSTMENT

BOLT

FIG. 33

NEUTRAL

LOCK GATE

MOTION CONTROL

LEVER

TRANSAXLE MOTION CONTROL LE VER

NEUTRAL ADJUSTMENT(See Fig. 33)

The motion control lever has been pre set at the factory and

adjustment should not be necessary.
•

Loosen adjustment bolt in front of the right rear wheel,

and lightly tighten.

•

Start engine and move motion control lever until tractor

does not move forward or backward.

•

Hold motion control lever in that position and turn engine

off.

•

While holding motion control lever in place, loosen the

adjustment bolt.

•

Move motion control lever to the neutral (N) (lock gate)

position.

• Tighten adjustment bolt securely.

NOTE:

If additional clearance is needed to get to ad just ment

bolt, move mower deck height to the lowest position.
After above adjustment is made, if the tractor still creeps

forward or backward while motion control lever is in neutral

position, follow these steps:
• Loosen the adjustment bolt.
• Move the motion control lever 1/4 to 1/2 inch in the

direction it is trying to creep.

•  Tighten adjustment bolt securely.
•  Start engine and test.
•  If tractor still creeps, repeat above steps until satis-

fied.

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or

replacement, it should be purged after reinstallation and

before operating the tractor. See “PURGE TRANS MIS SION”

in the Operation section of this manual.

TO REPLACE MOTION DRIVE BELT

(See Fig. 32)

Park the tractor on level surface. En gage parking brake.

For as sis tance, there is a belt installation guide decal on

bottom side of left footrest.
BELT REMOVAL -

• Remove mower (See “TO RE MOVE MOWER” in this

section of manual).

NOTE:

Observe entire motion drive belt and position of all

belt guides and keepers.
•   Disconnect clutch wire harness.
•   Remove clutch locator.
•   Remove belt from clutching idler and all stationary

idlers.

• Remove belt downward from engine pulley and around

electric clutch.

• Pull belt slack toward rear of trac tor. Carefully remove

belt up wards from trans mis sion input pulley and over

cooling fan blades.

BELT INSTALLATION -

• Carefully work new belt down around transmission

cooling fan and onto the input pulley.

• Pull belt toward front of tractor and roll belt around

electric clutch and onto engine pulley.

• Install belt through all stationary idlers and clutch ing

idler.

•   Reinstall clutch locator and tighten nut securely.
•   Reconnect clutch harness.
•   Make sure belt is in all pulley grooves and in side all

belt guides and keep ers.

• Install mower (See “TO IN STALL MOWER” in this sec-

tion of manual).

FIG. 32

02201

STATIONARY

IDLERS

TRANS MIS SION

IN PUT PULLEY

CLUTCHING

IDLER

ELECTRIC

CLUTCH

LOCATOR

CLUTCH

WIRE

HAR NESS

TO REMOVE WHEEL FOR REPAIRS

(See Fig. 34)

• Block up axle securely.
•

Remove axle cover, retaining ring and washers to allow

wheel removal (rear wheel contains a square key - Do

not lose).

• Repair tire and reassemble.

Содержание LT2218CMA

































Результаты поиска

Содержание LT2218CMA

Отзывы:

Похожие инструкции для LT2218CMA

Бренды по названию

Популярные бренды

Jonsered LT2218CMA, Руководство оператора

Результаты поиска

Содержание LT2218CMA

Отзывы:

Похожие инструкции для LT2218CMA

Бренды по названию

Популярные бренды