background image

 

4

 

 – 

 

English

 

INTR

 

ODUCTION

 

Dear Customer

 

,

 

Cong

 

ratulations on your choice to buy a Jonsered product!

We are convinced that you will appreciate with great satisfaction the quality and performance of our product for a very long time to 
come. The purchase of one of our products gives you access to professional help with repairs and service whenever this may be 
necessary. If the retailer who sells your machine is not one of our authorised dealers, ask for the address of your nearest service 
workshop.

It is our wish that you will be satisfied with your product and that it will be your companion for a long time. Think of this operator

 

 

manual as a valuable document. By following its

 

 

 content (using, service, maintenance etc) the life span and the second-hand value 

of the machine can be extended. If you will sell this machine, make sure that the buyer will get the operator

 

 

s manual.

Good luck on using your Jonsered machine!

Jonsered has a policy of continuous product development and therefore reserves the right to modify the design and appearance 
of products without prior notice.

Содержание HTE2123

























Отзывы: