Jonsered 1188S CE Скачать руководство пользователя

Страница: 80 / 96

Tighten the top chain with the adjustment screw. The correct tension is achieved when it is
possible to move the chain vertically about 1.5 to 3 cm from its center by hand.

Check the chain adjustments by extending and retracting the extensions a couple of times.

12.7. Cabin [option]

12.7.1. Adjust the slide pads in the cabin

Tighten the screws against the sliding pads, first upper (1)
and then lower (2) set screw.

Tightening method: Tighten 1/4 round. Tighten 1/4 round a
second time. Repeat on the other side.

If needed, hit with a rubber mallet against the locking plate
to ensure the right position of each sliding pad.

12.7.2. Tightening of screws and bolts in cabin

Tighten the fastening nuts shown in images A and B.

Maintenance and Service

Jonsered 1188S CE

Содержание 1188S CE

































































































Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды

Jonsered 1188S CE, Руководство оператора

Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды