background image

Page 3 - 2

Safety instructions

3

 

          

(7) Do not carry out any modifications, additions or conversions to the

device! This also applies to the installation and adjustment of safety
equipment.

(8) Spare parts must meet the technical requirements specified by the

manufacturer. This can only be guaranteed with original JOKE spare
parts.

(9) Any work on/with the device may only be carried out by qualified,

appropriately trained and authorised personnel. Pay attention to mini-
mum statutory age limits!

(10) Wear safety goggles when working with the handpiece for rotating

movements.

(11) Personnel undergoing training or in a general apprenticeship should

only be allowed to work with the machine under the constant supervi-
sion of an experienced operator!

(12) Restrain from any type of work that could jeopardise your safety.

(13) The device may only be used if all protective and safety equipment is in

place and in proper working order.

(14) Do not leave the device unattended when switched on!

(15) Stop and secure the device immediately in the event of malfunctions!

Faults must be remedied at once.

Содержание 0 005 400




















Отзывы: