Johnson JAR-5100 Скачать руководство пользователя страница 45

Страница: 45 / 79

PEDAL AXLE-PULLEY ASSEMBLY REPLACEMENT

PROCEDURE

(JPC/B)

Tools required:

Philips
screwdriver

C-clip pliers

Crank extractor

Coin

Hex key (4mm)

Open-end
wrench

(14&17 mm)

Procedure:

Remove the crank cover

and screw, then remove the
crank.

(Refer to page 3-5)

Loosen the screws
from the side cover with the
screwdriver, then remove
footpad, guard and side

cover.

Loosen the screw (A) and remove it (for the axle-pulley
assembly of the new design).

Remove the spring attaching the idler pulley to the frame
first, then loosen the screws attaching the bearing housing
to the axle-pulley assembly using the hex key (4mm)

(The spring replacement is dangerous. Take special
cautions during the operation

so you will not damage

both you and other

parts, then remove the front pulley)

Remove the c-clip (B) by using the c-clip pliers and using
the Bearing Puller remove the Bearing Housing

3-10 Revision: 1.0 Date: 2001/06/01

Содержание JAR-5100
















































































Результаты поиска

Содержание JAR-5100

Отзывы:

Похожие инструкции для JAR-5100

Бренды по названию

Популярные бренды

Johnson JAR-5100, Руководство по обслуживанию

Результаты поиска

Содержание JAR-5100

Отзывы:

Похожие инструкции для JAR-5100

Бренды по названию

Популярные бренды