Johnson Controls YJHJXH018BARR-FX Скачать руководство пользователя страница 17

Страница: 17 / 112

Domestic Air Conditioner

If Tr<Ts+, the outdoor system will be turned on again, the indoor fan will be at the cold air proof mode.

*Indoor fan control

manual control: You can choose high, medium, low and automatic speed control.

Automatic: When Tr<Ts, high speed.

When Ts=<Tr=<Ts+2

, medium speed.

When Tr> Ts+2

, low speed.

When the airflow speed has no delay from the high to low switching, the speed should be delayed for

3 minutes (remain at high speed for 3 minutes.) before the next switch.

*Airgate location control: the location for the airgate can be set according to your needs.

Coldair proof operation

1. The indoor operation within 4 minutes after the start up is as the following diagram, the air speed

can be raised only after the speed has reached a certain level.

2. 4 minutes after the start up of the indoor fan, the light airflow and the low airflow will be turned to the

set speed airflow.

3. In the cold air proof operation, the fan won’t stop after the start up.

4. During the cold air proof operation, the indoor system will continuously send ‘indoor high speed’

signals to the outdoor system.

* Residue heat sending. The indoor fan will send the residue heat at a low speed for 12 seconds.

If other conditions are satisified, when the compressor stops, the indoor system will operate at a light

speed. The indoor fan will stop when the coil temperature is below the ‘heat start temp 4’.

* Defrosting. When the system receives the defrosting signal from outdoors, the indoor fan will stop

and the indoor temperature display won’t change. At the time, any indoor coil malfunctions will be

neglected. When the outdoor defrosting finishes, the coil malfunction will still be neglected until the

compressor has been started up for 30 seconds. The indoor temperature display will not change and

the system operates at the cold air proof mode.

* Automatic heating temperature compensation: when the system enters the heating mode, the

temperature compensation (4) will be added. When the status is switched off, the compensation will

be erased.

5.1.5 strength operation

a. the system enters the mode after receiving the ‘strength signal’.

Send strength operation signal to the outdoor system.

The mode change finishes the strength operation.

Entering ‘mute’, you can have normal operation or signal control such as timing to finish the strength

operation.

Heat start temp 1

Heat start temp

Set speed

Low speed

Light speed

Fan/off

Keep the high

speed. The fan

doesn’t stop

Funcitions and Control

YJHJZH018BARRAFX

－ＳＭ

Содержание YJHJXH018BARR-FX

















































































































Результаты поиска

Содержание YJHJXH018BARR-FX

Отзывы:

Бренды по названию

Популярные бренды

Johnson Controls YJHJXH018BARR-FX, Руководство по обслуживанию

Результаты поиска

Содержание YJHJXH018BARR-FX

Отзывы:

Бренды по названию

Популярные бренды