manualshive.com logo in svg

Johnson Controls VMA18 Series, Руководство по установке, Страница: 21 / 26

Поделиться
Скачать
Johnson Controls VMA18 Series Скачать руководство пользователя страница 21

Note: 

Refer to the 

N2 Communications

Bus Technical Bulletin (LIT-636018)

 for the

N2 bus EOL termination rules. Refer to

the 

MS/TP Communications Bus Technical

Bulletin (LIT-12011034

) for the FC bus EOL

termination rules.

3.  If the field controller is a terminating device on

the N2 or FC Bus, set the EOL switch to ON. If

the field controller is not a terminating device

on the bus, set the EOL switch to OFF.

Note: 

When the EOL switch is set to ON,

the LED light on the face of the controller

is illuminated.

Commissioning

Use the following procedure to commission the

VMA18 controller:

1.  Download the control application to the VMA

controller using the CCT. Refer to the Controller

Tool 

Help (LIT-12011147)

.

2.  Commission the VAV Box. Refer to the 

Controller

Tool Help (LIT-12011147)

.

3.  Perform airflow balancing on the VAV box.

Refer to the 

VAV Balancing Tool Technical Bulletin

(LIT-12011087)

.

4.  Perform commissioning checkout procedures.

Refer to the 

Controller Tool Help (LIT-12011147)

.

CCT connects to the VMA through a laptop

computer using any one of the following connection

options: the MAP Gateway, BTCVT, the Wireless

ZigBee USB Dongle, or the wired BACnet

®

 Ethernet

to MS/TP Router. These connection options require

additional hardware listed in Table 9.
For more detailed N2 VMA controller commissioning

information, refer to the 

N2 VMA Application Note

(LIT-12011829).

Note:

• The MAP Gateway serves as a replacement

for the BTCVT, which is no longer available

for purchase, but continues to be supported

on select controllers.

• CCT 10.3 auto-detects when BTCVT can be

used or not, based on the controller model

and the corresponding CCT Release mode.

•

- BTCVT can be used with controllers

that contain CCT Release mode 10.2 or

earlier firmware.

Metasys

 controllers from Release 9.0 or

earlier support BTCVT.

- BTCVT cannot be used with controllers

that contain CCT Release mode 10.4.

Metasys

 Release 10.0 controllers

use CCT Release mode

10.4, therefore BTCVT is not

supported with these controllers.

VMA1826/1832 VAV Controller Installation Guide

21

Содержание VMA18 Series



























Отзывы:

Нет отзывов