background image

CCS Smart Equipment Control Board for Single Packaged Unit (SPU) Controller Installation

Instructions

1

Applications

The new SE-SPU101x controllers replace the 
RTU-100x controllers. All the RTU100x controllers are 
discontinued, including the RTU-1003-0 VAV SPU 
controller. The new SEC product offering provides new 
controller options.

The SE-SPU101x-1 SEC Unit Control Board (UCB) is a 
member of the Smart Equipment Controller (SEC) 
product family. The controller is designed to run a pre-
engineered HVAC zoning application and provide the 
inputs and outputs required for this application.

North American Emissions Compliance

United States

Canada

Installation

Special Tools Needed

wire strippers

small flat-head screwdriver

22 AWG (0.65 mm) 3-conductor, twisted, shielded
cable with a drain wire

Note:

This drain wire is used only to group the

shielded cable. Do not use this drain wire as a
connection to the board.

wire nuts for 22 AWG drain wire

electrical tape

Mounting

The manufacturing facility mounts the controller. All of 
the required power wiring, internal unit sensor wiring, 
and output wiring is completed and tested at the 
factory. The control application required for the specific 
UCB is factory configured and ready for operation.

Wiring

Field Wiring Connections

In addition to power connections, the UCB requires a 
communication bus connection. Address selection is 
required for networking with a CCS Building 
Automation System (BAS).

Power Wiring

The SEC UCB controller is factory wired for 24 VAC 
power. 

This equipment has been tested and found to 
comply with the limits for a Class A digital device 
pursuant to Part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection 
against harmful interference when this equipment is 
operated in a commercial environment. This 
equipment generates, uses, and can radiate radio 
frequency energy and, if not installed and used in 
accordance with the instruction manual, may cause 
harmful interference to radio communications. 
Operation of this equipment in a residential area 
may cause harmful interference, in which case the 
users will be required to correct the interference at 
their own expense.

This Class (A) digital apparatus meets all the 
requirements of the Canadian Interference-Causing 
Equipment Regulations.

Cet appareil numérique de la Classe (A) respecte 
toutes les exigences du Règlement sur le matériel 
brouilleur du Canada.

IMPORTANT:

The 24 VAC power should not be 

shared with other network devices. Sharing power to 
other network devices may cause noise, 
interference, and ground loop problems. You may 
damage the controller by sharing power to other 
devices.

CCS Smart Equipment Control Board for Single Packaged 
Unit (SPU) Controller

Installation Instructions

SE-SPU1011-1, SE-SPU1012-1

Code No. LIT-12011479

Issued June 16, 2015

Содержание SE-SPU101 Series









Отзывы: