Johnson Controls PCV1617 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 28

Johnson Controls PCV1617 Скачать руководство пользователя страница 1

PCV1617 and PCV1632 VAV Box Controllers

Installation instructions

Applications

The PCV1617 and PCV1632 are programmable digital controllers designed for VAV box applications

that communicate through the BACnet

®

MS/TP protocol. The controllers feature an integral digital

pressure sensor, a damper actuator, and a 32-bit microprocessor. The controllers' small package

size facilitates quick field installation and efficient use of space without compromising high-tech

control performance. The PCV controllers connect easily to either the networked or to the non-

communicating sensor for zone air temperature sensing.

Communications Protocol

The PC family controllers and network sensors communicate using the standard BACnet protocol,

based on the ANSI/ASHRAE 135-2008. The BACnet protocol is a standard for ANSI, ASHRAE, and the

International Standards Organization (ISO) for building controls.
PCV field controllers are BTL-listed as BACnet Application Specific Controllers (B-ASCs).

North American Emissions Compliance

United States

This equipment has been tested and found to comply with the limits for a Class A digital device

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when this equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area may cause harmful

interference, in which case the users will be required to correct the interference at their own

expense.

Canada

This Class (A) digital apparatus meets all the requirements of the Canadian Interference-Causing

Equipment Regulations.
Cet appareil numérique de la Classe (A) respecte toutes les exigences du Règlement sur le

matériel brouilleur du Canada.

Installation

Observe these guidelines when installing the PCV1617 and PCV1632 controllers:
• Transport the PCV controller in the original container to minimize vibration and shock damage to

the PCV controller.

• Do not drop the PCV controller or subject it to physical shock.

Part No. 24-10143-1299 Rev B
2019-03-22

(barcode for factory use only)

CH-PCV1617, CH-PCV1632

*2410143299B*

1
2
3
...
»

Содержание PCV1617





























Отзывы:

Нет отзывов