manualshive.com logo in svg

Johnson Controls IOM3731-0A, Руководство по установке, Страница: 3 / 14

Поделиться
Скачать
Johnson Controls IOM3731-0A Скачать руководство пользователя страница 3

Observe these additional guidelines when mounting

an expansion module in a panel or enclosure:
• Mount the expansion module so that the

enclosure walls do not obstruct cover removal or

ventilation through the expansion module.

• Mount the expansion module so that the power

transformer and other devices do not radiate

excessive heat to the expansion module.

• Do not install the expansion module in an airtight

enclosure.

Figure 2: Mounting positions

DIN rail mount applications

Mounting the controller horizontal on 35 mm DIN

rail is the preferred mounting method. To mount a

controller on 35 mm DIN rail, complete the following

steps:

1. Securely mount a 20 cm (8 in.) or longer section

of 35 mm DIN rail horizontally and centered in

the desired space so that the controller mounts

in the horizontal position.

2. Pull the two bottom mounting clips outward

from the controller to the extended position.

3. Hang the controller on the DIN rail by the hooks

at the top of the (DIN rail) channel on the back

of the controller, and position the controller

snugly against the DIN rail.

4. Push the bottom mounting clips inward (up) to

secure the controller on the DIN rail. To remove

the controller from the DIN rail, pull the bottom

mounting clips out to the extended position

and carefully lift the controller off the DIN rail.

Wall-mount applications

To mount the controller directly on a wall or other

flat vertical surface, complete the following steps:

1. Pull the two bottom mounting clips outward

and ensure they are locked in the extended

position.

2. Mark the mounting hole locations on the wall

using the dimensions in Figure 3 and one of the

mount positions shown in Figure . Or hold the

controller up to the wall or surface in a proper

mount position and mark the hole locations

through the mounting clips.

3. Drill holes in the wall or surface at the marked

locations, and insert appropriate wall anchors

in the holes (if necessary).

4. Hold the controller in place, and insert the

screws through the mounting clips and into the

holes (or anchors). Carefully tighten all of the

screws.

Important: 

Do not overtighten the mounting

screws. Overtightening the screws may

damage the mounting clips.

Mounting features and dimensions

Figure 3: Back of controller showing extended

mounting clips, DIN rail channel, and mounting

dimensions, mm (in.)

IOM3731-0A Expansion Input/Output Installation Guide

3

Содержание IOM3731-0A















Отзывы:

Нет отзывов