manualshive.com logo in svg

Johnson Controls IOM3731-0A, Руководство по установке, Страница: 11 / 14

Поделиться
Скачать
Johnson Controls IOM3731-0A Скачать руководство пользователя страница 11

The expansion module cover is held in place by

four plastic latches that extend from the base

and snap into slots on the inside of the housing

cover.

To remove the expansion module cover,

complete the following steps:

1. Place your fingernails under the two cover

lift tabs (Figure 1) on the sides of the housing

cover and gently pry the top of the cover away

from the base to release the cover from the two

upper latches.

2. Pivot the top of the cover further to release it

from the lower two latches.

3. Replace the cover by placing it squarely over

the base, and then gently and evenly push the

cover onto the latches until they snap into the

latched position.

Setting the End-of-Line (EOL) switch

Each field controller has an EOL switch, which, when

set to ON, sets the controller as a terminating device

on the bus. The default EOL switch position is OFF.

Figure 10: End-of-Line switch positions

To set the EOL switch on a field controller, complete

the following steps:

1. Determine the physical location of the

controller on the FC bus.

2. Determine if the controller must be set as a

terminating device on the bus.

Note: 

For detailed information regarding EOL

termination rules and EOL switch settings on

FC buses, refer to the 

MS/TP Communications

Bus Technical Bulletin (LIT-12011034)

.

3. If the controller is a terminating device on

the FC bus, set the EOL switch to ON. If the

controller is not a terminating device on the

bus, set the EOL switch to Off.

When a controller is connected to power with its

EOL switch set to ON, the amber EOL LED on the

controller cover is lit.

Commissioning

You commission expansion modules with the

Controller Configuration Tool (CCT) software,

using NxE Passthru, Bluetooth (with BTCVT),

through Mobile Access Portal (MAP) Gateway at

version 4.2 or above. Refer to the 

Controller Tool

Help (LIT-12011147)

 for detailed information on

commissioning expansion modules.

Note: 

The MAP Gateway serves as a

replacement for the BTCVT, which is no longer

available for purchase, but continues to be

supported.

Troubleshooting

Observe the Status LEDs on the front of the

expansion module. Table 7 provides LED status

indicator information for troubleshooting the

expansion module.

LED status and states

Table 7: Status LEDs and description of LED states

LED label

LED color

Normal LED state Description of LED states

POWER

Green

On Steady

Off Steady = No Supply Power. The expansion module’s polyswitch/resettable

fuse may be open. Check output wiring for short circuits and cycle power to

expansion module.
On Steady = Power Connected

FAULT

Red

Off Steady

Off Steady = No Faults
On Steady = Device Fault
Blink - 2 Hz = Download or Startup in progress: not ready for normal operation

SA/FC BUS

Green

Blink - 2 Hz

Blink - 2 Hz = Data Transmission (normal communication)
Off Steady = No Data Transmission (N/A - auto baud not supported)
On Steady = Communication lost; waiting to join communication ring

IOM3731-0A Expansion Input/Output Installation Guide

11

Содержание IOM3731-0A















Отзывы:

Нет отзывов