Johnson Controls FX-PCV Series Скачать руководство пользователя страница 1

Страница: 1 / 22

FX-PCV Programmable Variable Air

Volume Box Controllers Installation

Instructions

Applications

The FX-PCV1610/1620 controllers are part of the Facility Explorer

Series Programmable Controller

(FX-PC) family. FX-PCV controllers feature an integral 4 Nm damper actuator and Differential

Pressure Transducer. FX-PCV controllers run pre-engineered and user-programmed applications

required to monitor and operate a wide variety of VAV boxes.
The FX-PCV controllers operate on an RS-485 BACnet

MS/TP Bus as BACnet Application Specific

Controllers (B-ASCs) and integrate into the web-based Facility Explorer system.

North American Emissions Compliance

United States

This equipment has been tested and found to comply with the limits for a Class A digital device

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when this equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area may cause harmful

interference, in which case the users will be required to correct the interference at their own

expense.

Canada

This Class (A) digital apparatus meets all the requirements of the Canadian Interference-Causing

Equipment Regulations.
Cet appareil numérique de la Classe (A) respecte toutes les exigences du Règlement sur le

matériel brouilleur du Canada.

Installation

Observe these guidelines when installing an FX-PCV controller:
• Transport the controller in the original container to minimize vibration and shock damage to the

FX-PCV Box controller.

• Do not drop the controller or subject it to physical shock.

Parts included

• One FX-PCV controller with removable bus and power terminal blocks
• One installation instructions sheet

Materials and special tools needed

• One screw or other type of fastener appropriate for the mounting surface

Part No. 24-10143-179 Rev. C
2019-03-22

(barcode for factory use only)

FX-PCV1610-0, FX-PCV1620-0

*2410143179C*

Содержание FX-PCV Series























Результаты поиска

Содержание FX-PCV Series

Отзывы:

Похожие инструкции для FX-PCV Series

Бренды по названию

Популярные бренды

Johnson Controls FX-PCV Series, Руководство по установке

Результаты поиска

Содержание FX-PCV Series

Отзывы:

Похожие инструкции для FX-PCV Series

Бренды по названию

Популярные бренды