Johnson Controls FEU2610 Series Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 15

Johnson Controls FEU2610 Series Скачать руководство пользователя страница 13

FEU2610 Field Equipment Controller Installation Instructions

13

When set to the INT position, the FEU26 is the

power source for the Binary Output and both sides of the load can

be wired directly to the OUTx and COMx terminals.

Setting the jumper to the EXT position isolates the Binary Outputs, and power must come from one or more
external sources. Do not wire the load directly to the OUTx and COMx terminals. Wire one side of the load to the
source and the other side of the load to the OUTx terminal. Wire the other side of the external power source to the
COMx terminal.

Analog Input Load Resistor Enable/Disable

The Analog Input Resistor Enable/Disable jumpers (J10 through J15) are located on the circuit board in the
controller cover. These jumpers can permanently connect the internal 4-20 mA, 100 ohm load resistor to the input
terminals. There is one jumper for each of the Universal Inputs. See

Software configuration of the Universal Input normally selects the enabling or disabling of the analog input load
resistor. In cases when the analog input load resistor must be left connected even when power is OFF to the
controller, set this jumper to the ENABLE position.

Note:

This jumper must be in the DISABLE position for all Universal Input modes other than 4-20 mA.

Commissioning

Commission the FEU26 with the Controller Configuration Tool (CCT). Refer to

Controller Tool Help (LIT-12011147)

for details.

Troubleshooting

Use

to troubleshoot the FEU26.

J14

UI5

J15

UI6

Table 5: Status LEDs (Part 1 of 2)

Name

Color

Normal

Descriptions

Power/PWR

Green

On Steady

Off Steady = No Power
On Steady = Power is supplied by Primary Voltage.

Fault/FLT

Red

Off Steady

Blink - 2 Hz = Download or Startup in progress, not ready for normal operation
Off Steady = No Faults
On Steady = Device Fault; no application loaded; Main Code download
required, or if controller is in Boot mode.

Table 4: Jumper Labels and UI Inputs (Part 2 of 2)

Jumper Position

Universal Input (UI)

Figure 13: Analog Input Resistor Jumper Positions

Jumper

Pins

Jumper positioned
on top two pins

Jumper positioned
on bottom two pins

ENABLE

DISABLE (Default)

F

IG:

An

a

_

Jm

p

r

«
...
11
12
13
14
15
»

Содержание FEU2610 Series
















Отзывы:

Нет отзывов