Johnson Controls FAC3613 Скачать руководство пользователя страница 24

Страница: 24 / 24

Table 9: FAC3613 Advanced Application Field Equipment Controller

United States:

UL Listed, File E107041, CCN PAZX, UL 916, Energy Management

Equipment
FCC Compliant to CFR47, Part 15, Subpart B, Class A

Canada:

UL Listed, File E107041, CCN PAZX7 CAN/CSA C22.2 No. 205, Signal Equipment

Industry Canada Compliant, ICES-003

Europe:

Johnson Controls declares that this product is in compliance with the essential

requirements and other relevant provisions of the EMC Directive.

Australia and New Zealand:

RCM Mark, Australia/NZ Emissions Compliant

Compliance

BACnet International:

BACnet Testing Laboratories™ (BTL) Protocol Revision 15 Listed

and Certified BACnet Advanced Application Controller (B-AAC), based on the ANSI/ASHRAE

135-2016

The performance specifications are nominal and

conform to acceptable industry standard. For

application at conditions beyond these specifications,

consult the local Johnson Controls office. Johnson

Controls shall not be liable for damages resulting from

misapplication or misuse of its products.

Product warranty

This product is covered by a limited

warranty, details of which can be found at

www.johnsoncontrols.com/buildingswarranty.

Single point of contact

APAC

Europe

NA/SA

JOHNSON CONTROLS
C/O CONTROLS PRODUCT
MANAGEMENT
NO. 32 CHANGJIJANG RD NEW
DISTRICT
WUXI JIANGSU PROVINCE 214028
CHINA

JOHNSON CONTROLS
WESTENDHOF 3
45143 ESSEN
GERMANY

JOHNSON CONTROLS
507 E MICHIGAN ST
MILWAUKEE WI 53202
USA

For more contact information, refer to

www.johnsoncontrols.com/locations.

are subject to change without notice.

www.johnsoncontrols.com

Содержание FAC3613

























Результаты поиска

Содержание FAC3613

Отзывы:

Похожие инструкции для FAC3613

Бренды по названию

Популярные бренды

Johnson Controls FAC3613, Руководство по установке

Результаты поиска

Содержание FAC3613

Отзывы:

Похожие инструкции для FAC3613

Бренды по названию

Популярные бренды