Johnson Controls FAC3613 Скачать руководство пользователя страница 20

Страница: 20 / 24

To make use of this feature, ensure the DIP switches

are set to the desired address and wire the input

and output terminals. Apply power to the FAC

controller and connect to the device with either a

MAP Gateway or MS-DIS1710-0 Local Display to view

the points in the controller. The FAC controller will

report an Operational status even though there is

no true application loaded. CCT will not be able to

commission or upload the device as a result until

a true application is downloaded. The application

name displayed will be the address of the controller

followed by the model of the controller and “Default

State”.
For example, a FAC3613 controller whose DIP

switches are set to 8 would have the default state

application name of “8-FAC3613 Default State”.
The default state creates I/O points for all

connections on the input and output terminals.

It assumes all Universal Inputs (UIs) are Nickel

temperature sensors. The default state also takes

input from a Network Sensor at address 199. If there

is no connected Network Sensor, the startup of this

default state will be delayed by 30 seconds as the

controller attempts to establish connection with the

sensor.

Commissioning Controllers

You commission BACnet MS/TP controllers with the

(Controller Configuration Tool ) CCT software. The

controller can be connected using NxE Passthru,

Bluetooth (using BTCVT), or through MAP 4.2+/

BACnet Router (Mobile Access Portal (MAP) Gateway

at version 4.2 or above). Refer to

Controller Tool

Help (LIT-12011147)

for detailed information on

commissioning field controllers. Beginning at

CCT Release 13, the firmware package files are

orderable separately; they are not included with

CCT. They are obtained from the Metasys software

licensing portal, and are loaded and licensed on the

computer/server that is running CCT. .

Note:

The MAP Gateway serves as a

replacement for the BTCVT, which is no longer

available for purchase, but continues to be

supported.

Firmware Package File

The MS-FCP-0 equipment controller firmware

package files are required for CCT to configure and

commission the controllers. The firmware package

files also allow you to upgrade an existing controller

to the latest firmware release available for that

controller.
Beginning at CCT Release 13, the firmware package

files are orderable separately; they are not included

with CCT. They are obtained from the

Metasys

software licensing portal, and are loaded and

licensed on the computer/server that is running

CCT.
For additional information about the firmware

package files, refer to the

CCT Installation Instructions

(LIT-12011259)

Troubleshooting Controllers

Observe the Status LEDs on the front of the field

controller and see the table below to troubleshoot

the controller. To troubleshoot an integral or

local controller display, refer to the

DIS1710 Local

Controller Display Technical Bulletin (LIT-12011270)

FAC3613 Advanced Application Field Equipment Controller Installation Guide

Содержание FAC3613

























Результаты поиска

Содержание FAC3613

Отзывы:

Похожие инструкции для FAC3613

Бренды по названию

Популярные бренды

Johnson Controls FAC3613, Руководство по установке

Результаты поиска

Содержание FAC3613

Отзывы:

Похожие инструкции для FAC3613

Бренды по названию

Популярные бренды