Johnson Controls FAC2611 Скачать руководство пользователя страница 5

Страница: 5 / 24

Figure 5: SA bus terminal block wiring

Note:

The SA PWR terminal supplies 15 VDC. The SA

PWR terminal can be used to connect (daisy chain)

the 15 VDC power leads on the SA bus.

FC bus port

The FC bus port on the front of the controller is an RJ-12,

6-position modular jack that provides a connection for

the Mobile Access Portal (MAP) Gateway, the Bluetooth

Commissioning Converter, or the ZFR/ZFR Pro Wireless

Field Bus Router.
The FC bus port is connected internally to the FC bus

terminal block. For more information about the FC

Bus port functions, requirements, and ratings, see

Communications bus and power supply terminal block

rating and requirements table

. The FC bus port pin

assignment is shown in Figure 6.

Note:

• When the FAC is configured for N2 network

communication, the FC bus port is not used.

• The MAP Gateway serves as a replacement for the

BTCVT, which is no longer available for purchase,

but continues to be supported.

Figure 6: Pin number assignments for sensor, SA bus,

and FC bus ports on Field Controllers

SA Bus port

The Sensor (SA Bus) port on the bottom of the controller

is an RJ-12, 6-position modular jack that provides

a connection for MAP Gateway, the Bluetooth

Commissioning Converter (BTCVT), the VAV Balancing

Tool, specified network sensors, or other SA Bus devices

with RJ-12 plugs.
A DIS1710 Local Controller Display also can be connected

to the SA Bus port (but only on FEC models without

integral display and push buttons).
The Sensor port is connected internally to the SA

bus terminal block. For more information about the

Sensor port functions, requirements and ratings, see

Communications bus and power supply terminal block

rating and requirements table

. The Sensor Port pin

assignment is shown in Figure 6 (but only on FEC models

without integral display and push buttons).

Supply power terminal block

The 24 VAC supply power terminal block is a gray,

removable, 3-terminal plug that fits into a board-mounted

jack on the top right of the controller.
Wire the 24 VAC supply power wires from the transformer

to the HOT and COM terminals on the terminal plug as

shown in Figure 7. Do not use the middle terminal on the

supply power terminal block. See

Communications bus

and power supply terminal block rating and requirements

table

for more information about the Supply Power

Terminal Block.

FAC2611 Advanced Application Field Equipment Controller Installation Guide

Содержание FAC2611

























Результаты поиска

Содержание FAC2611

Отзывы:

Похожие инструкции для FAC2611

Бренды по названию

Популярные бренды

Johnson Controls FAC2611, Руководство по установке

Результаты поиска

Содержание FAC2611

Отзывы:

Похожие инструкции для FAC2611

Бренды по названию

Популярные бренды