1
8
Technical Information
Service Manual
Function introduction for combination buttons
Operation guide
Replacement of batteries in remote controller
1. Energy-saving function
1. After putting through the power, press "ON/OFF" button on remote controller to turn on the air conditioner.
2. Press "MODE" button to select your required mode: AUTO, COOL, DRY, FAN, HEAT.
3. Press "▲" or " ▲ " button to set your required temperature. (Temperature can’t be adjusted under auto mode).
4. Press "FAN" button to set your required fan speed: auto, low, medium and high speed.
5. Press "SWING" button to select fan blowing angle.
● During operation, point the remote control signal sender at the receiving window on indoor unit.
●
The distance between signal sender and receiving window should be no more than 24.3ft (8m), and there should be no obstacles
between them.
● Signal may be interfered
with
in
a
room where there is fluorescent
light
or wireless telephone; remote controller should be close to
indoor unit during operation.
● Replace new batteries of the same model when replacement is required.
● When you don’t use remote controller for a long
period of
time, please take out the batteries.
● If the display on remote controller is fuzzy or there’s no display, please replace batteries.
2.
46.4°F (
8
℃)
heating function
3.
Lock
function
4. Temperature display switch
-
over function
Under cooling mode, press "TEMP" and " CLOCK" buttons simultaneously to start up or turn off energy-saving function. When energy-saving
function is started up, "SE" will be shown on remote controller, and air conditioner will adjust the set temperature automatically
according to factory setting to reach to the best energy-saving effect. Press "TEMP" and "CLOCK"
buttons simultaneously again to exit
energy-saving function.
Note:
● Under energy-saving function, fan speed is defaulted at auto speed and it can’t be adjusted.
● Under energy-saving function, set temperature can’t be adjusted. Press "TURBO" button and the remote controller won’t send signal.
● Sleep function and energy-saving function can’t operate at the same time. If energy-saving function has been set under cooling mode,
press
ing
sleep button will cancel energy-saving function. If sleep function has been set under cooling mode, start
ing
up the energy-
saving
function will cancel
the
sleep function.
Under heating mode, press "TEMP" and "CLOCK" buttons simultaneously to start up or turn off 8
℃
heating function. When this function is
started up, " " and "8
℃
"
will be shown on remote controller, and the air conditioner keep
s
the heating status at 8
℃
. Press "TEMP" and
"CLOCK" buttons simultaneously again to exit 8
℃
heating function.
Note:
● Under 8
℃
heating function, fan speed is defaulted at auto speed and it can’t be adjusted.
● Under 8
℃
heating function, set temperature can’t be adjusted. Press "TURBO" button and the remote controller won’t send signal.
● Sleep function and 8
℃
heating function can’t operate at the same time. If 8
℃
heating function has been set under cooling mode, press
ing
sleep button will cancel 8
℃
heating function. If sleep function has been set under cooling mode, start
ing
up the 8
℃
heating function
will
cancel sleep function.
● Under
℉
temperature display, the remote controller will display 46
℉
heating.
Press
"▲" or "▲"
simultaneously to turn on or turn off
the lock
function. When lock function is on,
icon is displayed on remote controller. If
you operate the remote controller, the
icon will blink three times without sending
a
signal to the unit.
Under OFF status, press " ▲ " and "MODE" buttons simultaneously to switch temperature display between
℃
and
℉
.
1. Press the back side of remote controller marked with " ", as shown in the fig
ure
, and then
push
out the cover of battery box along the arrow direction.
2. Replace two 7# (AAA 1.5V) dry batteries, and make sure the position of "+" polar and "-" polar
are correct.
3. Reinstall the cover of battery box.
Note:
signal sender
battery
Cover of battery box
remove
reinstall
