Johnson Controls Bentel Security tyco ABS128M50, Руководство по установке

Страница: 46 / 132

Ø
If the transceiver does not receive a valid signal from
a wireless siren, or a repeater, inside the
Wireless
Supervisory Window
, the control panel generates the
System
>
System Fault
event.
+
The
System
>
System Fault
event does not distin-
guish the wireless siren or the repeater that causes
it; this information can be found in the logger.
Valid values: Disabled, After 1 Hour(s), After 2 Hour(s),
After 4 Hour(s), After 8 Hour(s), After 12 Hour(s), After
24 Hour(s).
Default: After 2 Hour(s).
Tamper Enabled If this option is disabled, the trans-
ceiver does not report opening and removal from the
mounting surface.
Default: enabled.
Jam Detection If this option is enabled, the trans-
ceiver detects and reports RF jamming, based on the
selected value:
Ø
UL 20/20 , continuous RF jamming for 20 seconds,
suitable for installation in the USA;
Ø
EN 30/60 , 30 seconds of accumulated jamming
within 60 seconds, suitable for installation in Europe.
Default: EN 30/60.
The control panel signals the RF jamming detected by
the transceiver, as shown in Table 8.
n
Wireless Detectors
The Wireless Detectors option group is for wireless de-
tectors enrolling, as described below.
# In the column #, choose a free position to enroll the
wireless device.
Label In the
Label
option, enter a meaningful label for
the wireless device: the entered label is used to identify
the device in the
Zones
option group, for associating the
device with a logical zone.
Valid Values: up to 16 characters.
Default: Detector 1, Detector 2, etc.
Device ID In the
Device ID
option, enter the ID number
that you find on the wireless device: if a valid ID number
is entered, the console shows the corresponding type of
wireless device, and the options that you can set for that
type of device. Set the wireless device options as indi-
cated in “Wireless device options” on page 128.
Enter all zeros to remove a wireless device.
Valid Values: three digits for the device type, and four
digits for the serial number.
Default: 000-0000.
n
Wireless Sirens
The
Wireless Sirens
option group is for wireless sirens
enrolling, as described below.
# In the column #, choose a free position to enroll the
wireless device.
Label In the
Label
option, enter a meaningful label for
the wireless device: the entered label is used to identify
the device in the
Outputs
option group, for associating
the device with a logical output.
Valid Values: up to 16 characters.
Default: Siren 1, Siren 2, etc.
46 Expandable Hybrid Control Panel
Keypad
Device Event Class Icon Message
Transceiver Device lost Tamper
s
WLS rec. lost
Transceiver Tamper Tamper
b
WLS receiver
Transceiver RF jamming Tamper
b
WLS receiver
Wireless Detector Device fault Fault — Fail detect. nn
Repeater Low battery Fault — No
Repeater AC fault Fault — No
Repeater Device fault Fault — No
Repeater Tamper Tamper
b
Generic Tamper
Repeater Device lost Tamper — No
Wireless Siren Low battery Fault — No
Wireless Siren Device fault Fault — No
Wireless Siren Tamper Tamper — Generic Tamper
Wireless Siren Device lost Tamper — No
Keyfob Device fault Fault — No
Table 8 The control panel signals the events relating to wireless devices with the occurrence of the event indicated in
the Events and Actions column; the keypad lights the light indicated in the Class column and, the LCD keypad shows
an X above the icon indicated in the Icon column; ...