Johnson Controls Bentel Security tyco ABS128M50, Руководство по установке

Страница: 128 / 132

Wireless device options
Table 24 describes the wireless device options. For fur-
ther information, refer to the devices’ instructions.
128 Expandable Hybrid Control Panel
Option Description
Activity LED If you enable this option, the activity LED of the device flashes to indicate that the device is
operating.
If you disable this option, the activity LED is off.
Optional settings: disabled (default), or enabled.
Alarm Direction This option sets the detection direction. The right and left directions refer to the point of view
of the installer while observing the detector in its mounting position.
Optional settings:
Left to right , Right to left , or Both (default).
Alarm Hours This option sets the detector to report alarm always, or only when it is dark.
Optional settings:
Day and Night
(default), or
Night only
.
Alarm LED If you enable this option, the alarm LED of the device signals the motion detection.
If you disable this option, the alarm LED is off.
Optional settings: disabled, or enabled (default).
Anti-Masking If you enable this option, the control panel reports a fault when the microwave sensor is
masked:
Ø
event
Zone Fault/Masking
, relative to the detector's zone, occurs
Ø
the keypad signals the Fail detect. nn fault, where nn is the detector number
Ø
the even logger memorizes the Masked Zones event, and the zone label
Optional settings: disabled, or enabled (default).
Anti-Masking PIR This option sets the sensitivity level of infrared sensor anti-masking.
If you select
Low Sensitivity or High Sensitivity , the control panel reports a fault when the de-
tector's infrared sensor is masked:
Ø
event
Zone Fault/Masking
, relative to the detector's zone, occurs
Ø
the keypad signals the Fail detect. nn fault, where nn is the detector number
Ø
the even logger memorizes the Masked Zones event, and the zone label
Optional settings: Disabled , Low Sensitivity (default), or High Sensitivity .
Auto Tamper
Alarm
If you enable this option, the siren sounds a continue tone when it cannot communicate with
the control panel, and when it is open, or removed from the mounting surface.
Optional settings: disabled (default), or enabled.
Cold: Threshold This option sets the threshold for the cold temperature alert. Event Temperature Below Cold
Threshold on Zone occurs when the temperature measured by the device remains below the
temperature set in this option, for the time set in Cold: Wait before alert option. The event re-
stores when the temperature measured by the device remains at least 1°C above the
temperature set in this option, for the time set in
Cold: Wait before restore option.
Optional settings: from -29°C to 39°C (default 19°C)
Cold: Wait before
alert
This option sets the time that the temperature measured by the device must be below the
temperature set in the
Cold: Threshold
option, before
Temperature Below Cold Threshold on
Zone
event occurs.
Optional settings:
Fast
,
1 Minutes
,
2 Minutes
,
10 Minutes
(default),
15 Minutes
,
20 Minutes
, or
30 Minutes
.
Cold: Wait before
restore
This option sets the time that the temperature measured by the device must be at least 1°C
above the temperature set in the
Cold: Threshold option, before Temperature Below Cold
Threshold on Zone event ends.
Optional settings: Fast , 1 Minutes , 2 Minutes , 10 Minutes (default), 15 Minutes , 20 Minutes , or
30 Minutes .
Detection Range This option sets the detection range of the detector:
Ø
Minimum
= 2 m for BW-IRT, 3 m for BW-902
Ø
Medium
= 4 m for BW-IRT, 5 m for BW-902
Ø
Maximum
= 6 m for BW-IRT, 8 m for BW-902
Optional settings:
Minimum
,
Medium
, or
Maximum
(default).
Table 24 Wireless device options.