background image

3

CONTENTS

PAGE

1.

GENERAL

1.1

Description of the appliance ............................................................................. 4

1.2

Technical safety equipment ............................................................................. 6

1.2.1

Gas control valve ............................................................................................. 6

1.2.2

Control panel .................................................................................................... 6

1.2.3

Operation of the water heater ......................................................................... 7

1.2.4

Combustion products discharge safety device ................................................ 7

1.3

Technical information ....................................................................................... 8

1.3.1

Dimensions ....................................................................................................... 8

1.3.2

Technical data ................................................................................................ 10

2.

FOR THE INSTALLER

2.1

Installation instructions ................................................................................... 12

2.1.1

Installation ...................................................................................................... 12

2.1.2

Water connections ......................................................................................... 13

2.1.3

Gas connection .............................................................................................. 15

2.1.4

Flue system .................................................................................................... 15

2.1.5

Flue down draught safety device .................................................................. 15

2.1.6

Electrical connection ...................................................................................... 15

2.2

Commissioning ............................................................................................... 16

2.3

Removing and replacing the control panel front cover ................................... 17

2.4

Setting the gas pressure ................................................................................ 17

2.5

Removing and replacing the inner door .......................................................... 18

2.6

Temperature regulation .................................................................................. 18

2.7

Converting to another type of gas ................................................................. 19

2.8

Maintenance ................................................................................................... 19

2.8.1

Sacrificial anode ............................................................................................ 19

2.8.2

Cleaning ......................................................................................................... 20

2.8.3

Inspection of the internal waterside surfaces ............................................... 20

2.8.4

Spare parts .................................................................................................... 20

2.9

Inlet combination ............................................................................................. 20

2.10

Gas smell ....................................................................................................... 20

2.11

Condensation ................................................................................................. 20

2.12

Important warning .......................................................................................... 20

3.

FOR THE USER

3.1

Commisioning ................................................................................................. 21

3.2

Use ................................................................................................................. 21

3.3

Fault finding .................................................................................................... 22

4.

WARRANTY

. .................................................................................................. 23

5.

Appendix 1

. .................................................................................................. 25

Содержание SCE 100-95 G





























Отзывы: