background image

Vision

 Es-Plus

 

//

 

Vending

 

 

 

 

 

MNP141GBV00                  Date: 2011/04/29 Rev. 0                          PAGE 22 OF 24                                        

is not obstructed anywhere along its path. Wait until it is completely dry before 
reinstalling it. 
 
?  In general, keeping all internal areas that are visible to consumers clean increases 
sales and improves the image of the machines.  
 
?  To access the lower trays (restocking area) open the machine’s exterior door and take 
out the trays one at a time sliding them along their guides. 
 
?  There is a window on the back of the machine to allow air to circulate into it. This area 
and the cooling unit condenser, which is just next to it, should be cleaned periodically 
with a brush or compressed air to ensure it is not clogged with papers, bags or dust. 
 
?  The machine should never be cleaned with a water jet. 
 
?  The machine’s interior should always be dry to ensure it works properly . 
 
?  When handling the cooling unit, always do so with the machine turned off and make 
sure that you do not bend any pipes, as they could break and produce a gas leak. 
 
?  It is very important never to touch any parts where there is LIVE VOLTAGE such as 
the power box and the wiring supplying the LED lights. To access these areas, open the 
machine’s outside door and use a screw driver to remove the metal boxes protecting 
these components. 
 
?  Access to servicing area should only be permitted to persons with a knowledge of and 
practical experience in the machine, particularly with regard to health and safety. 
 
? To clean the exterior of the machine, use a moist cloth with warm water and dry with a 
soft cloth. 
 
?  In case of persistent stains (grease, drinks, etc.), do not apply abrasive products. Do 
not use a cleaning spray! Use a solution of water and alcohol. 

8.3. 

Recyclable 

If you need to dispose of packaging materials consult your local authorities for recycling 
information. 
 

Do not throw away any electronic circuit as many of the materials that they 
are made of are recyclable. 
 

To manage the equipment as waste once the client has decided to dispose of it, 

Jofemar

 has set up a collection system with an Integrated Management System 

(ECOLEC). Please consult us for information about recycling. 

Содержание Vision ES-PLUS

























Отзывы: