Joab EcoDrive VL10U страница 21 Скачать руководство пользователя | Manualshive

Страница: 21 / 57

background image

Safety-Wires

All skips must be properly secured onto the
vehicle before driving. This can be done using
manually placed securing equipment, such as
chains. Alternatively, JOAB's hydraulic safety-
wire system can be purchased. JOAB's safety-
wire system is built into the skip-loader and
allows for fast and secure fastening of a skip
onto the vehicle.

The safety-wire system can be operated using
the control panel or JOAB's radio controller.
The control panel and radio controller must be
in

Function_3

mode to operate the safety wires.

Refer to

"Radio Controller", on page 19

for further information regarding the operation of the

safety wires via the radio controller and to

"Control Panel - Button Functions", on page 10

for

operation via the control panel.

When the safety-wires are tightened correctly, the LED for the respective safety wire button will
illuminate constantly on the radio controller. The middle LED on the control panel buttons will
illuminate, when tightened correctly. The system tightens the safety-wires to 90 bar.

Make sure that the safety-wires are correctly tightened before driving the vehicle.
The LED for each safety-wire must be constantly illuminated. Failure to do so can
lead damage or injury.

NOTE:

If the radio controller is switched from Function_3 mode, the LEDs for the safety-wires

indicating that they are correctly tightened, will not be illuminated if Function_3 mode is selec-
ted again. This is a safety feature. Pressing the safety-wire buttons again to tighten the wires
will first verify if the wires are correctly tightened, and if so, the LEDs will illuminate once again.

Rotator

A rotator can be purchased for skip-loaders.
This makes it possible to rotate a skip
270 degrees when suspended from the
lifting-arm. The rotator is mounted onto the
skip-loader's boom-pipe (see

Components", on page 2

).

Operation of the rotator is done using the con-
trol panel or JOAB's radio controller. First
make sure

Function_2

mode is active. Then

press button 11 to unlock the rotator. Use button 9 to rotate the rotator clock-wise (CW) and
button 10 to rotate it counter-clock-wise (CCW).

15

Operation | Extra Options

EcoDrive VL10-VL18 manual: 1021046 Edition 2 | 2022-05-02

«
...
19
20
21
22
23
...
»

Содержание EcoDrive VL10U


























































Отзывы:

Нет отзывов

Похожие инструкции для EcoDrive VL10U

Бренд: ZETRON Страницы: 3

Бренд: Badger Meter Страницы: 48

Бренд: rav Страницы: 120

Бренд: RAM Страницы: 32

Бренд: Ravaglioli Страницы: 90

Бренд: Mesa Страницы: 58

Бренд: T.L. FAHRINGER Страницы: 26

CIRCOtransfer 30 E

Бренд: wagner solar Страницы: 32

Бренд: PROCRAFT Страницы: 25

Бренд: Sumner Страницы: 10

Бренд: Lincoln Electric Страницы: 15

Бренд: Genie Страницы: 44

UWI 230 TP AC/DC

Бренд: Unitor Страницы: 25

Ampac MAN3053-1

Бренд: Halma Страницы: 6

Бренд: WIA Страницы: 44

Бренд: WIA Страницы: 24

Бренд: Revo Страницы: 6

Бренд: Pro Spot Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды