JLG 680S Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 530

background image

SECTION 3 - CHASSIS & TURNTABLE

3-26

3121234

Housing-Spindle Sub-Assembly

NOTE:

Refer to Figure 3-18., Housing-Spindle Assembly.

NOTE:

Spray a light film of oil on all component parts during

assembly.

SAFETY GLASSES MUST BE WORN DURING THE ENTIRE HOUSING-SPINDLE

SUBASSEMBLY.

1.

Press Bearing Cup (1C), position A, into Housing (1E)
using appropriate pressing tool (See back of manual).

2.

Turn Housing (1E) over and place into pressing base.

Press nine Studs (1H) into Housing (1E).

NOTE:

Use enough pressure to press in studs. Don t use excessively

high pressure to press in studs or Housing may crack. Make
sure head of stud contacts face of flange on Housing.

NOTE:

Spray a generous amount of oil on bearings during instal-

lation.

3.

Press Bearing Cup (1C), position "B", into Housing (1E)
using “B” Bearing Cone pressing tool (see back of man-

ual).

4.

Place Bearing Cone (1D), into Bearing Cup (1C), position

"B".

5.

Grease Seal (1B) lip and press seal into Housing (1E)

using seal pressing tool (see back of manual) until seal is

flush with end of Housing.

6.

Turn Housing (1E) over and lower onto Spindle (1A).

7.

Install Bearing Cone (1D) into Bearing Cup (1C), position
"A". and lightly press on Bearing Cup using the “A” Bear-

ing Cone pressing tool (see back of manual) while rotat-

ing Housing (1E) in both directions to seat bearings.

8.

Place Bearing Spacer (1F) on top of Bearing Cone (1D).

9.

Using retaining ring pliers, install Retaining Ring (1G)

into Spindle (1A) groove. Make sure ring is completely

seated in groove.

NOTE:

Extra bearing pre-load caused by pressing “A” Bearing

Cone (1D) must be removed. This should be done by plac-

ing a flat piece of steel or a pressing tool on the end of the

spindle, and then lightly striking the tool with a piece of
barstock. This should be adequate to remove any addi-

tional bearing pre-load.

DW2B Integral Brake Check

1.

Using appropriate fittings, connect hydraulic line from
hand pump to brake port.

2.

Check to see that brake is set by trying to rotate Input
Shaft (7). This can be accomplished by installing an
appropriate tool (any tool that can locate on the splines
of the Input Coupling (9), such as a mating splined shaft)
into Input Coupling (9).

3.

Bleed brake. Increase hydraulic pressure gradually while
trying to rotate the input until brake just starts to
release. Note this pressure. Make sure the pressure falls
into the appropriate range below.

4.

Increase pressure to 3,000 psi and hold for 30 seconds to
check for leaks. Repair leaks if necessary.

NOTE:

Make sure that brake re-engages when pressure is
released.

NOTE:

When done, make sure Input Coupling (9) is centered in
Spindle (1A) to make installation of motor possible without
release of brake.

BRAKE

CODE

BRAKE P/N

JUST RELEASE

PRESSURE RANGE (psi)

A

902337

185-230

B

902341

155-192

C

902342

125-155

D

902343

93-115

E

902345

132-172

«
...
76
77
78
79
80
...
»

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 680S

Бренд: WALTCO Страницы: 20

Бренд: dbx Страницы: 52

Бренд: CIGWELD Страницы: 116

Бренд: FAIE Страницы: 5

Бренд: Bard Страницы: 54

Бренд: Lampert Страницы: 22

WELDSKILL 200HF

Бренд: CIGWELD Страницы: 60

Бренд: Weldability Страницы: 12

Prism Medical 303090

Бренд: Handicare Страницы: 26

Бренд: ESAB Страницы: 46

AutroMaster ISEMS

Бренд: Autronica Страницы: 94

Бренд: Elektra Beckum Страницы: 52

Бренд: human care Страницы: 24

Бренд: ato form Страницы: 32

Бренд: Jackle Страницы: 36

Бренд: WARPP Страницы: 14

Бренд: FAAC Страницы: 16

Weighing System

Бренд: NAUSICAA Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды