113538 - 7
Telephone 01422 822282
27
Safety Related Circuits
Make a complete operational check of all safety related
circuits:
• Door Switch(es)
• Hi-Limit Thermostats
• Sail Switch
Make a complete operational check of all operating controls.
Tumbler Coating
The tumbler is treated with a protective coating. We suggest
dampening old garments or cloth material with a solution of
water and nonflammable mild detergent and tumbling them in
the tumbler to remove this coating.
Microprocessor Programs / Selections
Each microprocessor controller (computer) has been
preprogrammed by the factory with the most commonly used
parameter (program) selections. If computer program changes
are required, refer to the computer programming manual which
was shipped with the dryer.
Preoperational Instructions __________
IMPORTANT:
For more detailed information regarding the
microprocessor controller (computer), refer to the
microprocessor user’s manual included with the dryer.
Coin Models
Microprocessor Controller (Computer)
When the microprocessor controller (computer) is in the ready
state, the L.C.D. screen will display “Ready, Insert $XX.XX
(amount) to Start”.
Insert coin(s). Once the correct “Amount to Start” has been
inserted, the L.C.D. will display “Select Temperature”.
Select temperature by pressing “HI,” “MED,” or “LO.” The
cycle will start and the L.C.D. will display the Dry Cycle selected
and the remaining time.
The dryer will continue through the drying and cooling cycles,
until the vended time has expired.
NOTE:
To stop the dryer, open main door. Continuation of
the cycle will resume only after the door has been closed
and any one of the three temperature selections is pressed.
Non-Coin Models
Microprocessor Controller (Computer)
The L.E.D. display reads “READY” (no cycle in progress).
Press the letter on the keypad corresponding to the cycle
desired (e.g. key “D”).
The dryer will then start (i.e. blower, tumbler, and heat).
The L.E.D. display will read MANUAL DRYING CYCLE D,
___MIN REMAIN.
NOTE:
The dryer can be stopped at any time by pressing
the “STOP/CLEAR” key, at this time the dryer will go into a
cycle pause. If the “STOP/CLEAR” key is pressed again at
this point, the cycle that was in progress will be cancelled
and returned to the “READY” state.
When the programmed drying time has expired, the non-coin
microprocessor controller (computer) will proceed into the Cool
Down Cycle.
Once the Cool Down Cycle begins at the end of the heat cycle,
the L.E.D. display will read COOL DOWN TEMP ___/___
MINUTES remaining. At the end of the heat cycle, the dryer
will shut off the heat and continue the fan and tumbler until
the Cool Down Time or temperature is reached.
Shutdown Instructions ________________
If the dryer is to be shutdown (taken out of service) for a period
of time, the following must be performed:
Discontinue power to the dryer either at the external disconnect
switch or the circuit breaker.
Discontinue the heat supply:
Gas Models – Discontinue the gas supply.
Shut off external gas supply shutoff valve.
Shut off internal gas supply shutoff valve located in the gas
valve burner area.
Service / Parts Information ___________
Service
Service must be performed by a qualified trained technician.
If service is required, contact the distributor from whom the
equipment was purchased. If the distributor cannot be
contacted or is unknown, contact the JLA Service Department
for a distributor in your area.
NOTE:
When contacting the Service Department, be sure to
give them the correct model number and serial number so
that your inquiry is handled in an expeditious manner.
Parts
Replacement parts should be purchased from the distributor
from whom the equipment was purchased. If the distributor
cannot be contacted or is unknown, contact the Parts
Department for a distributor in your area. Parts may also be
purchased directly from the factory by calling the JLA Parts
Department at 01422 822282 or you may FAX in your order at
01422 824390.
NOTE:
When ordering replacement parts from the
distributor or the manufacturer, be sure to give them the
correct model number and serial number so that your parts
order can be processed in an expeditious manner.
Содержание SD35
Страница 16: ...16 JLA Limited 113538 7 SD35 ...
Страница 17: ...113538 7 Telephone 01422 822282 17 SD50 SD80 ...
Страница 30: ...Part No 113538 7 04 21 17 ...
