JLA SD20 Скачать руководство пользователя страница 3

Страница: 3 / 24

113545 - 3

Telephone 01422 822282

IMPORTANT

You must disconnect and lockout the electric

supply and the gas supply or the steam supply

before any covers or guards are removed from

the machine to allow access for cleaning,

adjusting, installation, or testing of any equipment

per OSHA standards.
Please observe all safety precautions displayed

on the equipment and/or specified in the

installation manual included with the dryer.
Before installation, check that the local

distribution conditions, nature of gas and

pressure, and adjustment of the appliances are

compatible.

CAUTION

Dryer(s) should never be left unattended while

in operation.

When discarding or storing your old clothes

dryer, remove the door

Lorsque vous entreposez ou mettez votre

sécheuse au rebut, enlevez-en la porte

“Caution: Label all wires prior to disconnection

when servicing controls. Wiring errors can cause

improper operation.”
«Attention: Au moment de l’entretien des

commandes, étiquetez tous les fils avant de les

débrancher. Des erreurs de câblage peuvent

entraîner un fonctionnement inadéquat et

dangereux.»

WARNING

Children should not be allowed to play on or near

the dryer(s). Children should be supervised if

near dryer(s) in operation.
Under no circumstances should the dryer door

switch(es), lint door/drawer switch(es), or heat

safety circuit(s) ever be disabled.
Do not modify this appliance.
The dryer must never be operated with any of

the back guards, outer tops, or service panels

removed. Personal injury or fire could result.
The dryer must never be operated without the

lint filter/screen in place, even if an external lint

collection system is used.

FOR YOUR SAFETY

Do not dry mop heads in the dryer. Do not

use dryer in the presence of dry cleaning

fumes.

The dryers must not be installed or stored in an

area where it will be exposed to water and/or

weather.
The wiring diagram for the dryer is located behind

the control panel.

Table of Contents _____________________

List of Acronyms _____________________

HVAC

Heating, Ventilating, and Air-Conditioning

in WC

Inches of Water Column

L.C.D.

Liquid Crystal Display

L.P.

Liquid Propane

OSHA

Occupational Safety and Health Administration

Underwriters Laboratory

Safety Precautions .............................. 4

Specifications ...................................... 6

Installation Procedures ....................... 8

Service / Parts Information ............... 20

Service ...................................................................20
Parts .......................................................................20

Warranty Information ........................ 21

Returning Warranty Cards .....................................21
Warranty ................................................................21

Routine Maintenance......................... 21

Data Label Information ...................... 22

Содержание SD20

























Результаты поиска

Содержание SD20

Отзывы:

Похожие инструкции для SD20

Бренды по названию

Популярные бренды

JLA SD20, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SD20

Отзывы:

Похожие инструкции для SD20

Бренды по названию

Популярные бренды