SB-POL-RNGR/SYS INSTR_SKU# 011278
s t e P 1 2
C o n G R a t u l a t I o n s !
You have completed the installation for this model!
Enjoy your new Stealthbox®! Go out in the woods and get
dirty!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
s t e P 1 1
Along the inner edge of each speaker housing there are
two screw holes that will need to have pilot holes drilled
and then have the supplied 1/4x 1” Button Head Allen Bolts
installed through the flanges and the floor, under the floor
there should be a fender washer against the floor and, a
1/4-20 Locknut installed to secure the speaker housings to
the floor of the vehicle.
s t e P 1 0
Run the wire from each of the kick panels to the amplifier
location, slide the kick panels into place using the opposite
method from what was done to remove the OEM kick pan-
els. Position the housings so that the screw holes along the
frame rail line up with the holes in the enclosure. Using the
OEM hardware, attach each enclosure to the frame rails of
the vehicle.
s t e P 9
Install a piece of the included Self Adhesive Gasket Material
along the outer edge of each frame rail where the OEM kick
panels had been attached.
Page 3 • JL Audio, Inc 2008
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU#011278 ©10-15-2008 • Printed in USA • ©2008 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902
#6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign
patents pending. For more detailed information please visit us online at
www.jlaudio.com.
(954) 443-1100
w w w. j l a u d i o . c o m
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
I n C l u d e d H a R d W a R e
1) Custom Aluminum Bracket
1) 3/8-16x 1 1/2” Hex Head Bolt
1) 3/8-16x 1” Hex Head Bolt
1) 3/8 x 1 1/4” Fender Washer
4) 3/8 Split Locking Washer
1) 3/8 Flat Washer
1) Square U-Bolt (with washers and, nuts) 4) 1/4x 1” Button Head Allen Bolt
4) 1/4-20 Lock Nut
1) 1/2x 1” Custom Aluminum Spacer
s P e C I F I C a t I o n s
Subwoofer Enclosure Type:
Acoustic Suspension (sealed)
Driver Type:
M10W5
Nominal Impedance:
4 Ohms
Continuous Power Handling:
250 Watts (RMS)
Kickpanel Enclosure Type:
Infinite Baffle
Driver Type:
M770-CCX
Nominal Impedance:
4 Ohms
Continuous Power Handling:
100 Watts (RMS)
P o W e R R e C o m m e n d a t I o n
JL Audio recommends using a high quality amplifier such as the JL Audio M4500. The diagram below shows the
recommended crossover and input settings for the M4500 when being used to power your Stealthbox
®
.
The JL Audio M4500 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
