SB-GM-TAHOSCNSL/10W1v3_INSTR_SKU#011220
C O N G R A T U L A T I O N S
You have completed the installation for this model!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
S T E P 2 8
Attach the speaker wire to the terminal.
In reverse order from
Step 14
to
Step 1
, replace the factory
components back together.
S T E P 2 7
From under the vehicle, place the supplied fender washers, flat
washers, lock washers and then hex nuts onto each protruding
socket cup set screw and secure. Adjust the amount of
exposed thread on each cup set screw if necessary.
Note: For added protection, it is recommended that
you apply a bead of silicone between the vehicle
and the fender washer. After the bolt assembly is
tightly secured, it is also recommended that vehicle
under-coating material is applied to the exposed
assembly.
S T E P 2 6
Place the wire harness to the left side of the Stealthbox
®
.
Page 6 • JL Audio, Inc 2016
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 011210 - 09.20.2016 • Printed in USA • ©2016 JL Audio, Inc.
For more detailed information please visit us online at www.jlaudio.com.
(954) 443-1100
w w w. j l a u d i o . c o m
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
I N C L U D E D H A R D W A R E
(2)
3-inch x 3-inch Wax Squares
(2)
3/8-16 x 2-1/4-inch Socket Cup Set Screw
(2)
3/8-inch x 1 1/4-inch Fender Washer
(2)
3/8-inch-16 Hex Nut
(2)
3/8-inch Split Lock Washer
S P E C I F I C A T I O N S
Enclosure Type:
Acoustic Suspension (sealed)
Driver Type:
10W1v3-2
Nominal Impedance:
2 ohms
Continuous Power Handling:
300 Watts
P O W E R R E C O M M E N D A T I O N
JL Audio recommends using a high quality amplifier such as the JL Audio XD300/1v2.
The diagram below shows the recommended crossover settings for the XD300/1v2 when being used to power
your Stealthbox
®
.
The JL Audio XD300/1v2 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location:
6.5-inch / Front Doors
Fits JL Audio Models:
TR650-CSi, TR650-CXi, C2-650x, C2-650,
C5-650x, C5-650 & ZR650-CSi
Rear Speaker Size / Location:
6.5-inch / Rear Doors
Fits JL Audio Models:
TR650-CSi, TR650-CXi, C2-650x, C2-650,
C5-650x, C5-650 & ZR650-CSi