background image

I N S T A L L A T I O N   G U I D E 

for the 

SMS-C-CTS/PREM

SMS-C-CTS/BASE 

SKU#  94553/94554

2008 & Up Cadillac CTS/CTS-V   

Thank you for choosing a JL Audio StealthMod® System for your automotive sound system.  

With proper installation, your new vehicle-specific audio system  

will deliver years of listening pleasure.

We strongly recommend that you have your new StealthMod® System installed by your authorized  

JL Audio dealer. The installation professionals employed by your dealer have the necessary tools 

and experience to disassemble and reassemble your vehicle properly.  If you prefer to perform your 

own installation, please read this installation guide completely before beginning the process.

  

If you choose to perform the installation yourself, it is absolutely vital that 

the Stealthbox

®

 be properly mounted to the vehicle according to these 

instructions.  Failure to mount the enclosure properly presents two problems:  
1) The sub-bass performance will suffer due to the movement of the enclosure 

caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision 

or sudden deceleration.

Continued on Next Page 

SMS-C-CTS  INSTR_SKU#  011357

INSTALLATION  

D I F F I C U L T Y :

5

5

OUT   

OF

ESTIMATED TIME:

         5+ HOURS

S T E A L T H B O X ®   S P E C I F I C A T I O N S

 

Enclosure Type:

  Sealed

Driver Type:

  10TW3-D4

Nominal Impedance:

  2 ohms

Continuous Power Handling:

  400 watts (RMS method)

I N C L U D E D   E Q U I P M E N T

(1) HD-RLC

Premium System Only:                                        Base System Only:

(1) XD700/5 Amplifier                                            (1) XD500/3 Amplifier
(1) C5-650cw Speakers                                          (1) Pair C5-650x Speakers
(1) Pair C2-350x Speakers
                

I N C L U D E D   H A R D W A R E

 

(1) Rear Bracket                                                       (1) Amplifier Bracket
(1) Side Bracket                                                       (4) 1/4 - 20 x 5/8” Pan Head Screw
(2) 3/8 - 16 x 1” Hex Bolt                                        (4) 1/4 “ Flat Washer
(4) 3/8” Flat Washer                                                (4) 1/4 - 20 Keps Nut
(3) 3/8” x 1-1/4” Diameter Flat Washer                  (1) 8’ Power Wire
(5) 3/8” Lock Washer                                              (1) 18” Ground Wire
(5) 3/8 16 Hex Nut                                                  (1) 8’ Remote Turn-on Wire
(3) 3/8 -16 U-Nut                                                     (1) 4’ 12 Gauge Speaker Cable
(3) 3/8” x 2-1/4” Set Screw                                      (1) Mini Fuse Holder
(2) 6mm x 1.0 Flange Nut                                      (1) 3 amp Mini Fuse
(4) 0.80 Thin Foam Strip                                        (1) XD-MFB-MAXI Fuse Holder
(2) 0.875 Thick Foam Strip                                     (1) XD-MAXI-60 60 amp Fuse
(1) XB-MGLU Ground Lug                                     (1) XD-CLRAICY-1F2M Y-adaptor

Premium System Only:                                         Base System Only:

(5) Speaker Wire to RCA Adaptor                          (3) Speaker Wire to RCA Adaptor
(1) 38’ 16 Gauge Speaker Cable                             (1) 32’ 16 Gauge Speaker Cable
(2) CTS-V Door Speaker Adaptor                           (2) CTS Door Speaker Adaptor
(2) Dash Speaker Adaptor                                      (2) 12 ohm, 10 watt resistor / 2.2 uf capacitor
(24) #8 x 1-1/4” Pan Head Screw                            (8) #8 x 7/8” Pan Head Screw
(4) #8 x 3/4” Pan Head Screw                                 (24) #8 x 3/4” Pan Head Screw
(4) Speed Clip                                                          (8) Speed Clip

                                                                            

   (2) Crossover Bracket

StealthMod

®

Содержание SMS-C-CTS/BASE














Отзывы: